How can I create a hard source in Comsol Multiphysics?

Nathan Mastrange Lopes @Nathan-Mastrange-Lopes

18 April 2021 0 1K Report

Hello,

I am using the software comsol Multiphysics, RF Module with transient interface to simulate a non-linear conductivity, and i need to excitate two metal rods with a voltage signal by using a hard source. How could I program this kind of source?

Badges
Science topic

Similar topics
Cognitive Science
Thinking

More Nathan Mastrange Lopes's questions See All

How can CHARMM-GUI be used for protein-ligand interaction ?

My protein is a transmembrane protein, therefore i need to construct a transmembrane using CHARMM-GUI. Can someone please suggest me a tutorial for the same.

24 June 2024 5,044 1 View

Is there any equipment that replaces GPC/SEC in carrageenan characterization?

22 June 2024 2,361 3 View

Does anyone have this article in PDF and could they pass it on to me?

Paper: Wang, A.G., Luo, G.H., 1990. Quantitative relation between the reaction of hydroxylamine and superoxide anion radicals in plants. Plant Physiol. Commun. 6, 55–57.

19 June 2024 7,283 0 View

Is energy minimisation necessary step before molecular docking for protein-ligand interaction?

I have to perform molecular docking on 2 ligands (A structure-absent in literature and B structure-sourced from PubChem) therefore, is energy minimisation necessary for both?

14 March 2024 7,560 3 View

Is it possible for small molecule ligands to show significant heat release in control ITC run?

I am trying to optimize my control titration for ITC so that I can ensure my ligand to protein traces are reliable. My small molecule is stored in DMSO. I have been very careful to avoid buffer...

14 February 2024 9,147 3 View

Slight increase in heat transfer at the end of ITC trace?

Hello, I have recently switched from doing ligand into protein for ITC because my ligand is in DMSO and has low solubility at 10% DMSO; therefore, now I am doing protein into ligand -- the heat...

09 February 2024 4,680 1 View

Any tips on reverse ITC, protein into ligand?

Hello, I am having an ITC issue because I cant increase my ligand concentration due to solubility issues. I know there is past literature on reverse titrations being acceptable. I am more asking...

06 February 2024 5,564 2 View

How to rule out buffer mismatch in ITC Curve?

Hello, I am doing ITC and getting repeatable curves that look very promising. After reading some articles, it seems the biggest challenge to avoid is buffer mismatch. Is there a way to rule out...

18 January 2024 1,224 5 View

How can I put AutoDock4 reading my file?

Good afternoon, I am using AutoDock4 to do docking of a protein with 2 cobalts in the active site. I added the parameters of the cobalt in both the AD4_parameter.dat file and to the...

14 January 2024 6,033 0 View

ITC Software not fitting correctly?

Hello, I have had moderate success with ITC but most of my issues have been with the Nano Program in fitting. I have a clear curve but the program is not fitting it correctly, does anyone have a...

22 December 2023 9,331 1 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

What do you consider to be the most relevant elements of EEG for studying cognitive biases?

I've seen articles that primarily focus on alpha and beta activity in the frontal regions, but these studies often compare healthy subjects with those having various pathologies. I haven't seen a...

31 July 2024 7,259 1 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

How to calculate conductivity using Electrochemical Impedance Spectroscopy's Nyquist plot?

Hello everyone, I am new to this characterization but watching videos on youtube I have already plotted a Nyquist plot (Z' and -Z'') and already fitted models on my material using Zsim. But now I...

29 July 2024 1,376 0 View

Is it possible to do transient simulation in HFSS in presence of magnetic biasing?

I have designed magnetic material with different biasing conditions in HFSS. Now I want to give an RF AC signal and do a transient simulation in HFSS. Is it possible to do in HFSS? Please help me...

24 July 2024 9,319 5 View

How to get LP fiber modes directly from Comsol?

Hi there, I'm new to modelling with comsol. I would like to ask if it is possible for comsol to output linearly polarized (LP) modes? I tried modelling a simple single mode fiber with an enlarged...

23 July 2024 4,019 3 View

Element deletion problem in ABAQUS/Explicit solver using Cohesive elements?

I had a problem for so long. I could easily delete elements in ABAQUS implicit solver but I needed to use VUMAT so I had to have Explicit solution but the element did not disappear for so long. I...

23 July 2024 10,032 0 View

Provided that the shale conductivity termed here x increases with temperature, how could we compute it at reservoir temperature ?

one could use Waxman and Thomas (1974) work?

22 July 2024 6,637 0 View