How can I covert Radial Magnetic field data to cartesian grid?

More Bharat Singh Rawat's questions See All

Any research paper call for publication related to management or finance or economics?

It should be standard journal (Indexed)

01 March 2021 8,379 1 View

What will the effect on the inverse of large sparse (symmetric) matrix when a single (or a few) entries in the original matrix are perturbed?

The mathematics behind the inverse of large sparse matrices is very interesting and widely used in several fields. Sometimes, It is required to find the inverse of these kinds of matrices....

07 November 2020 4,842 3 View

How to calculate tilt angle and rotation angle of a membrane protein using gromacs 2018?

I have performed MD simulation to a trans membrane protein using gromacs 2018. Can anyone provide me way to calculate the tilt angle of the protein relative to bilayer? Also how can I calculate...

16 July 2020 7,917 1 View

What is the correct way to do the formulation of engine oil based nanofluid?

When we apply Tiwari-Das model of nanofluids to model the flow of engine oil based nanofluid, should it be done using the term which denotes relaxation time for velocity in momentum equation...

30 March 2020 8,383 2 View

Any researcher working on Alkaloids in India?

Any researcher working on the alkaloids(Trichodesmine, Junceine, Riddelline, Senecionine, Seneciphylline, Lycopsamine and Intermidine) in india. Need help regarding this.

03 March 2020 1,060 4 View

How to separate Adenosine and Inosine?

Hi everyone I have been trying to resolve adenosine and Inosine on HPLC column. The details are as follows: 1) Column dimension: 150mmX4.6mm, with 5 micron bead size. 2) Mobile phase: 20mM...

25 August 2019 3,420 3 View

How to clean organic matter deposited on quartz furnace tube. I used ethanol it did not work for me. Anyone please hep me?

I burnt waste organic matter (bagasse powder) at 400 C. Some sticky like substance is deposited on quartz tube. I want to clean that. Please help me.

30 July 2019 10,010 3 View

Could anyone suggest that for transfection in THP-1 cell line, out of electroporation or Lipofectamine LTX+plus reagent method, which one is better?

I have to transfect THP-1 cells, so I would want to know out of these two procedures which one will be more efficient or easier to do.

19 May 2019 8,157 5 View

In dissolution of semisolid dosage form using immersion cell, how can we identify whether the membrane is intact or broken without opening the cell?

while removing the retaining ring to check whether membrane is intact or not, a crack develops in the membrane. Is there any alternative way to check the membrane.

17 May 2019 489 2 View

Where to find the MATLAB code for Probabilistic Three-Log distance propagation model ?

Communication model IEEE 802.11p

14 March 2019 7,433 3 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

Compact antenna for the frequency range 1 MHz-5 MHz?

Hello everybody! I have a problem with developing a compact antenna for the 1MHz-5MHz frequency range. Tell me what type of antenna can be used and what books and articles to read to perform this...

27 February 2021 7,710 4 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

Is there a way to use waveguide ports for circular antenna design in CST?

Hi, whenever i use circular array i get this error "Waveguide ports must be aligned with Cartesian coordinate planes for the transient solver" Does anyone use circular array with waveguide ports?...

09 February 2021 3,609 8 View

How to model in HFSS or FEKO Free Space Material Characterization?

I am having trouble setting up this problem in HFSS or FEKO. In HFSS, I've tried both FEM and FEBI-IE solvers. With FEKO, I've tried it's MoM solver and default settings. I am would like model...

09 February 2021 375 2 View

What is best solution for optical metamaterial design calculation: HFSS, COMSOL, CST?

Dear all, Now I'm selecting FEM for design of metamaterials on NIR~VIS frequencies, and keeping 3 software: ANSYS HFSS, COMSOL with wave optics module, and CST STUDIO SUITE. Could you give me...

09 February 2021 9,517 2 View

Which journals (Q1,Q2) accept simulation based design and results of antenna if fabrication and testing facility is not available?

I need a list of good (preferably Q1,Q2) journals that will accept research papers prepared on designs done with the help of simulation software e.g CST, HFSS etc.

08 February 2021 9,636 5 View

How to achieve the sensitivity diagram of a sensor in CST?

I wanna design a sensor in CST 2021 for the first time and I don't know how to achieve the sensitivity diagram of the sensor in CST. Could you plz help me to do that? I appreciate your response...

26 January 2021 6,864 1 View

What is corrct way to define ports when simulating FSS and surface waves in CST?

I need to simulate a mushroom FSS and I'm struggling with the ports. What's the correct way to define them? Should I construct a proper SMA connectors, or is it enough to put a waveguide ports...

19 January 2021 6,590 4 View

Malcolm White

This means that the r and z components are the same for varying theta.

You can find the Bx, By and Bz components for each value of r and z and any value of theta that you wish, Bx = Br cos theta, By = Br sin theta, Bz = Bz. You can then interpolate between these values, on each xy plane to get a cartesian grid you want for each z , and then interpolate these in the z direction to get them at the z spacing you need.