How can I calculate inter railway vehicle coupler forces?

18 March 2015 1 9K Report

In the simulation of railway vehicle driving profile, coupler force calculation is required. Without the real time data, how to calculate coupler force coefficients and forces.

M. Ganesan

Please go through the below article which contains the useful references and information related to this question:

Second-order sliding mode controller with model reference adaptation for automatic train operation

Article, Jun 2017, Vehicle System Dynamics, 10.1080/00423114.2017.1330482

Badges
Science topic

More M. Ganesan's questions See All

Is there any cases algae not using the nutrient from the wastewater and grow normally?

I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...

08 August 2024 4,812 2 View

I have calcined my catalysts without flowing air from the compressed air cylinder will there be any problem with my reaction if i use that catalysts?

FYI Catalyst is MFI zeolite Si/Al = 140,25.40.11.5,15 I am using this catalyst to study methanol to DME conversion

25 July 2024 2,486 2 View

How can I measure arsenic concentration in a patient blood?

I intend to get an economical and accurate LAB TEST to measure arsenic concentration in blood sample.

23 July 2024 3,654 2 View

It is possible to conduct a structured written interview for a qualitative study?

In your opinion, I would like to know if a qualitative study with a structured interview can be conducted in writing. In other words, we sent out open questions and asked the interviewees to...

11 July 2024 4,163 4 View

What is Differential-Fed in microstrip patch ant? How it is design in CST studio? What is process and procedure to do Differential-Fed in CST studio?

What is Differential-Fed in microstrip patch antenna ? How it is design in CST studio? What is simulation process and procedure to do Differential-Fed in CST studio ?

08 July 2024 7,464 1 View

How to know the TM/TE modes in antenna design in CST studio?

How to know the TM/TE modes in antenna design in CST studio? Example: TM01 ,TM02 ,TM10, TM12, TM30 like this... how can identify the antenna is operate the above said mode? can any one explain...

08 July 2024 6,609 2 View

What is co-polarization and cross polarization? How can plot it from CST studio?

what is co-polarization and cross polarization? How can plot it from CST studio? what are steps and process for find out co-polarization and cross polarization from CST studio?

08 July 2024 7,869 1 View

Why in some degradation experiment the results doesn't fit first or second order kinetics ?

In an antibiotic degradation experiment using metals carbon composites to activate PMS, the results doesn't fit pseudo first or second order kinetics however the degradation efficiency is very...

26 June 2024 6,941 3 View

Why carrier Concentration decreases while increasing Temperature ?

Hi All . Recently, I conducted Hall measurement experiments at high temperatures on highly p-doped diamond with a doping concentration of 2.5×10^20 cm−3 During these experiments, I observed two...

23 June 2024 4,763 0 View

What are the best practices for increasing earth biomass?

I'm thinking of how to increase biomass to replace plastic and industrial waste.

23 June 2024 1,871 4 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Research Methodology - Impact of Corporate Reputation on Stakeholders Behaviors?

Please can anyone support with the survey questions based on RQ measures and propose how to do it in FMCG industry and include as well the role of brand equity Thanks

06 August 2024 949 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View