Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

How can we raise the figure when we writing a paper with Latex ?

Hi, everyone. I'm a starter to write a paper by Latex. But I have some difficulty using it. I'm writing the paper with 2 columns. And, there is one figure that occupies the 2 both-sides. I want to...

26 February 2021 3,738 3 View

Satellite orbit estimation using Recurrent Neural Network - what should I use?

Hello, I am a master's student studying in Yonsei Univeristy, Korea. I am trying to estimate the state of satellite, using Neural Network. Below is a simple flow of my study. 1. Train (t0 ~ t1)...

23 February 2021 6,383 3 View

What is the system of units used in the thermal conductivity by Spitzer and Harm?

23 February 2021 9,253 1 View

Not able to charge-discharge Li-ion coin cell at higher C rate ?

I am working on cathode material. I have made different Li-ion coin cell against Li metal using commercial available cathode materials such as LCO,LMO, LFP and NMC and also with the lab...

18 February 2021 1,450 3 View

How many days do we need to detect adoptively transferred Treg in the tumor site in tumor-bearing recipient mice?

Hello, I've got a plan to isolate mouse splenic Treg (WT and KO of target gene) and inject these CD45.2 Treg into tumor-bearing CD45.1 mice. My question is how many days do I need to wait to see...

11 February 2021 8,238 1 View

Is it possible to antibody labeling with FITC cause antibody disfuction?

Hello, I studied how much bound my test antibodies to the target antigen using FITC labeling to test antibodies. I tested 3 types of antibodies, the elisa binding affinity and cytotoxicity...

07 February 2021 8,335 2 View

Can you use MTS assay with cells cultured in media containing phenol red?

I am trying to run a cell viability assay with LN229, but these cells are cultured in DMEM which contain phenol red. Is the MTS assay sensitive to the additional of phenol red in the media? If so,...

03 February 2021 9,478 2 View

Lighting for open field test behavior assay?

I am currently setting up our lab's behavioral space to run the open field test in rats, and I am trying to figure out how to set up lighting to evenly illuminate the open field chamber (a 90 cm x...

26 January 2021 1,399 3 View

Is there a surface inactive water-soluble dye?

Hi guys, I'm looking for a water-soluble dye which is not surface inactive in order to observe (water in oil) emulsions; I don't prefer to use oil-soluble dyes. I've used rhodamin123,...

21 January 2021 8,496 2 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View