I am imaging very high concentration of E. coli solutions under confocal microscope. However, the bacterial cells always stick to the cover slip. Is there a coating which prevents their sticking ? Thanks !
I can offer to test a coated surface if you do not apply a thin coating of pure Ti with a thickness of no more than 150 nm.
Success in research
With respect
Emil Yankov
I have designed a MEMS-based IR thermal emitter and done the electro-thermal simulation to get the temperature profile of micro-heater. Now I want to check the radiation intensity vs wavelength...
14 October 2020 4,542 2 View
Also if possible please suggest me from where I can learn to write accurate subroutine for microstructure simulation because I am new on subroutine writing.
09 August 2018 6,126 1 View
10 May 2017 9,267 1 View
Hi, Can someone please help me with deriving that false/numerical/artificial diffusion is flow direction dependent and it is given as (image attached). also as per Patankar book , numerical...
30 October 2016 6,390 11 View
12 October 2016 357 5 View
Hi, since the Reynolds number is high for Turbulent flows, the viscous force are over powered by convective forces, meaning the dampening of disturbances will not be efficient. This results into...
27 July 2016 5,758 8 View
JC-1 dye monomers are excited at lower wavelengths and emit green, while the aggregates are excited at a higher wavelength and emit red. Why is this? Why do aggregates absorb at a higher...
13 June 2016 8,675 2 View
I am working on Organic solar cells and been trying to use Gold as an electrode (Anode). But my cells are shunted. I am wondering if a thin layer of MoO3 after the polymer blend could help gold to...
13 June 2016 3,852 3 View
06 June 2016 9,592 4 View
10 December 2015 2,694 12 View
i have problem in preparation of liver tissue with bad cell organelles and how i can adjust osmolarity
03 March 2021 8,890 1 View
I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...
01 March 2021 395 3 View
Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...
01 March 2021 8,220 2 View
Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !
01 March 2021 2,501 3 View
I am growing the cells on coverslips and transfecting the fluorescent tagged protein directly on them. Then i want to observe these cells under confocal microscope. Currently i am just using...
01 March 2021 6,142 3 View
I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....
28 February 2021 7,967 3 View
Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax
28 February 2021 6,685 2 View
I want to use 0.1% gelatin. Should that be made in PBS or sterile water? Should I autoclave the gelatin soln after making it in water/PBS?
28 February 2021 274 2 View
I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...
27 February 2021 6,801 3 View
I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...
27 February 2021 1,829 3 View