How can chose fitting method and model to data by GLM in the R?

More Mahboobeh Kiani-Harchegani's questions See All

Is deposition as a part of erosion?

Deposition is the end/stop of the erosion. it is a bit hard to say if it is or it is not.

29 July 2018 2,128 11 View

Is there a relation between the NPP and NDVI?

How to calculate the NPP from NDVI on image of Landsat 8?

04 May 2018 2,542 1 View

What is the difference between Particulate Organic Matter (POM) and Soil Organic Matter (SOM) determination method?

03 January 2018 8,814 5 View

Whether DESIRE is "Development of a system of indicators for a resource efficient Europe"?

Dears, Whether DESIRE is "Development of a system of indicators for a resource efficient Europe"? Please, describe about the DESIRE project goal. Best Regards, M. Kiani-Harchegani

05 April 2017 1,944 1 View

What is the standard error of measurement acceptable range?

what is the standard error of measurement acceptable range?

04 May 2016 9,933 4 View

What are whys and hows for Modelling in R?

What is first condition for modelling (GLM or GNM) in R? How much data is needed for modelling (at least)? are all data used in the model? Thank you

08 September 2015 8,089 1 View

What is comprehensive definition of splash erosion, the interrill erosion and rill erosion?

Please be introduced article or books.

06 July 2015 2,474 13 View

Which parameter plays the most important role in the transfer of water pollution; effective sediment or absolute sediment?

Which part of the sediment particle size is the most important? Clay or silt? why?

05 June 2015 8,977 4 View

How can I do GLM analysis (multivariate) in SPSS or R software for 4 factors and 12 depended variables?

I studied erosion evolution in simulation laboratory with 3 different rainfall intensities and 3 slopes . Also i measured splash erosion in the up and down of splash cup and in the up, medium and...

05 June 2015 2,311 3 View

Which parameter plays the most important role in the transfer of water pollution; effective sediment or absolute sediment?

Which part of the sediment particle size is the most important? Clay or silt? why?

03 June 2015 6,195 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

"A Markov-like Model for Patient Progression"?

A Markov-like Model for Patient Progression" Markov Chain Monte Carlo (MCMC) Markov Chain Monte Carlo (MCMC) is a powerful computational technique used to draw samples from a probability...

05 August 2024 10,079 0 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,153 4 View

Jochen Wilhelm

http://www.stat.columbia.edu/~gelman/arm/

http://www.wright.edu/~thaddeus.tarpey/ES714glm.pdf

http://people.bath.ac.uk/sw283/mgcv/tampere/glm.pdf

http://data.princeton.edu/wws509/notes/

http://data.princeton.edu/R/glms.html

http://www.statmethods.net/advstats/glm.html

http://statmath.wu.ac.at/courses/heather_turner/glmCourse_001.pdf

http://www.stat.columbia.edu/~martin/W2024/R11.pdf

... and there is much much more.

What is your problem, precisely?

Ali Gharaee

https://stat.ethz.ch/R-manual/R-devel/library/stats/html/glm.html