How Apply the three-dimensional constitutive laws instead of uni-axial constitutive laws in modeling the reinforced concrete members ?

08 May 2019 1 9K Report

When we write a code to simulate numerically the reinforced concrete members, always we think to increase the accuracy of our proposed model, in this regard always we face the following question:

How apply the three-dimensional constitutive laws instead of uni-axial constitutive laws for confined/unconfined/steel elements in numerical simulation modeling of the reinforced concrete members. Which 3-D models are suitable to apply for this purpose?

Kabir Sadeghi

I have developed a computer program (software) and I want implement suitable 3-D constitutive laws for materials in it, I do not want to apply the ready-made software developed by others. If you have a solution for it I will appreciate you.

More Kabir Sadeghi's questions See All

How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

How can I convert permeability unit from barrer to m^2 for using COMSOL MultiPhysics?

I am looking for gas permeability of PDMS for simulation in COMSOL MultiPhysics and using creeping flow , fluid and matrix properties. The permeability unit in COMSOL is m^2 whereas I have the...

08 February 2021 4,305 2 View

How to convert all .csv file to grayscale image and then save them?

I have a database of experiment .csv files. how to extract the feature from this .CSV file with max-min normalization? I need a matrix(with values between 0 to 255) to be converted to a grayscale...

04 February 2021 7,773 3 View

How to rectify the miscomputation of Pressure and Continuity in HVAC CFD Simulation Using OpenFOAM?

I'm using OpenFOAM to run a CFD study of thermal comfort within a hall. I'm using OpenFOAM v1912 and BouyantBoussinesq(Simple&Pimple)Foam solver. eI have 6 inlets and outlets each with specific...

21 December 2020 1,303 3 View

How to convert Shamsi dates into Christian dates in SPSS?

Hi I have a database in which there are several dates indexed as strings and in Shamsi format. I need them as dates (not strings) and prefer them to be Christian. I have tried "Date and Time...

14 December 2020 2,798 3 View

How to formulate or simulate FSI and 6DOF together?

hi every one I want to know, is there any way to formulate FSI and 6 DOF or simulate them together in CFD Softwares? for example FSI of a ship with 6 DOF in regular waves or irregular waves? thanks

01 November 2020 6,197 3 View

Is there any other microbes (except microalgae) that could efficiently remove nitrogen and phosphorus content from wastewater ?

I was studying the biological treatment (anaerobic) of wastewater biomass. I found that anaerobic bacteria take a comparatively longer time to biodegrade nitrogenous compounds. Is there any other...

28 October 2020 921 3 View

Would you suggest me a formula for calculating energy yield from biohydrogen and biomethane production?

I was looking for a formula to calculated the obtained energy yield via biohydrogen and biomethane production using anaerobic digestion process. The unit is in SI unit (x) mLH2/g VS and (y) mL...

20 October 2020 8,668 5 View

Is my retinal GFAP staining accurate?

I am doing immunofluorescence staining on retinal sections from RCS rats to assess GFAP. As shown in my attached image, the GFAP staining is not consistent with most literature I've seen with...

05 October 2020 8,105 3 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View