Hi all, which software can measure porosity accurately in surface coatings. Could you please help me?

More Venkateshwarlu Bolleddu's questions See All

Flower buds falling down after the floral dip agro transformation. any suggestion?

i am working with gene editing in bell pepper. i have done agro transformation by floral dip method. (LBA4404 carrying plasmid, at final pellet dissolved in 5% sucrose containing 0.02% silwet ). i...

13 May 2024 7,460 6 View

Is anyone using Hyperquad2013 Software ?

Please send me the software through any means or else I will send my research data send me the graphs and results. Thank you

01 February 2022 731 1 View

What are the best collection and storage practices & analytical parameters for medicinal plant resins, latex and gums?

Sir, Please suggest the analytical parameters for medicinal plant resins, latex and gums for their standardization. Further, pl suggest the best collection and storage practices (till their...

20 August 2015 2,957 3 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Can anyone provide me with molecular docking softwares/ websites?

Molecular docking software/ websites?

02 August 2024 8,704 7 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Can I proceed with Response Surface Methodology (RSM) with only one factor for further optimization?

I went for Plackett Burman Design for selecting the optimization factors of growth conditions for pesticide degradation. I started with 7 parameters. But, after the experiments and analysis, only...

29 July 2024 5,015 1 View

I am working on my Master's thesis on the biogeography of the genus Ruagea and I would like to ask, could someone help me to check whether my result?

I created a file with my outgroup and ingroup species using Beauti, ran it in BEAST, viewed it in Tracer, and then used TreeAnnotator to create a file that I imported into RASP. Could someone...

28 July 2024 2,979 1 View

I did hirshfeld surface analysis for molecule but did not find red spot and interaction surface in energy frame work, is it ok for research article ?

In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?

28 July 2024 2,988 0 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View