Hello, I suppose it depends on what your output files are. Not sure which module you are using, but the first thing to try is to run your simulation without outputs, and see if it runs. If it does, then increase the size of the output gradually. A glimpse of your pic mentions BW. If that is yje module you use, it can have very large outputs depending on the time steps specified in the module output specifications. Regards, Vladimir.
Did you try installing the latest service pack of the DHI MIKE software? There are also some hotfixes on their website.
https://www.mikepoweredbydhi.com/download/hotfixes-2014/mike21-150108?ref={8F7B09EA-2EFB-4EDC-A1BD-E03E7C8E4427ù
Cite
1 Recommendation
Ali Ghorban Sarvi
Iran University of Science and Technology
thank mr nazarali for your explain .
i'll check and try your suggestion.
Mostafa Nazarali
Cite
Samad Rasoulpour
Tarbiat Modares University
"encounter"
and if you have activated MikeZero . try run it as Administrator rights or change Output files Location to another partition with more available disk space
Cite
Similar questions and discussions
MIKE 21 Illegal Storage Access?
Question
5 answers
- Diana Sankar
Has anyone ever received the error 'Illegal storage access Abnormal completion' from MIKE? I am using the Data Extractor FM and at certain times this error comes up. Once I receive this error I don't seem to be able to extract data that I had previously extracted successfully. Any suggestions are appreciated.
What causes "Blow-Up Wave Height Too Large" Abnormal Run in Mike 21 Coupled Model (HD and SW)?
Question
7 answers
- Ariel Mohan
I am trying to run a coupled model (HD and SW MIKE 21), for a one year period (8760 time steps; 3600 time step interval). However, after approx 200 time steps there is an Abnormal Run error, 'Blow-Up wave height too large'. What are some reasons that would cause this, and some solutions?
Cause of "Error Blow Up - Elevation too large"?
Question
3 answers
- Niloufar Heidari
I'm trying to run Mike 21 FM HD model for a river with two boundaries. For upstream I got constant value of discharge and for downstream I set a Water Level time series which relate to the open boundary.
I wanted to test and run the model for 2 days with 30 sec time-step interval but I get an abnormal run completion in the first time step. And there is "Blow Up - Elevation too large". It shows very large water depth. Any suggestions are appreciated.
Thank you.
What causes "Blow-Up Elevation too large" abnormal run in Mike 3/21 Integrated Model (HD and ST)?
Question
5 answers
- Ahmet Altunsu
Hi, i am trying to run HD and ST model with MIKE 3/21 Integrated Model for a coastal area for 1 year with 600 sec timestep interval but there is an abnormal error in the middle of the year. It's 'Blow-up elevation too large'. When I examine the result, there is an anormal elevation values (about 30000 meter) in some nearshore cells. So I changed the timestep interval, resolution but didnt worked. Also, when I runned only HD model, model worked without a problem. But when HD and ST run coupled, there was an error.
So if there is anyone who experience or knowlegde about this issue, can you help me?
Thank you.
How to create a bathymetry input file for MIKE 21?
Question
8 answers
- Chiranjivi Jayaram
Hi,
I am learning MIKE 21 model and I would like to create input bathymetry file from GEBCO 30 Arc Second data for north coastal Bay of Bengal. Which one do I need to follow? Bathymetry or mesh generator? I have generated the coast line (land / water boundary) from the shape file and converted to .xyz format and stuckup for further steps.
" illegal storage access". Can you help me in solving this error?
Question
13 answers
- Amir Siahsarani
Dear Mr. /Mrs. I have problem during the running of Mike DHI 2014 Service Pack 3 which is emerged as illegal storage access. By my search, I have know that this problem can be solved by installing MIKE 21 HOTFIX 08-01-2015. However, there is no possibility for me to download this software due to lack of hotfix file in server. Can you help me in solving this problem? Many thanks. Amir Siahsarani
Error with Hydrodynamic Simulation on Mike Zero?
Question
Be the first to answer
- Daniel Olatunde
My hydrodynamic simulation went from 0 to 100% immediately on Mike Coupled Model FM. And no results was generated afterwards. I don’t know what the problem is.
I forced the model with the tidal potential data and wind data.
What could the problem be?
I didn’t get an error message, which is another reason why I’m confused.
How to download and import GEBCO data on MIKE 21?
Question
3 answers
- Daniel Olatunde
I recently downloaded Geo Tiff data from GEBCO. I converted the data to XYZ file, but I found out the XYZ data didn’t align with the exact coordinates on MIKE 21. Is there any reason as to why this is the case? Are the coordinate systems of the two platforms different or what?
Please, I’m confused.
What is the meaning of this error and how to solve it? - mike 21 - Coupled Model FM?
Question
1 answer
- Nahla Hazem
What is the meaning of this error and how to solve it? - mike 21 - Coupled Model FM
Related Publications
Ảnh hưởng hạ tầng giao thông đến thoát lũ sông Bàn Thạch
Article
- Nguyễn Viết Quang Tuấn
- Nguyễn Quang Bình
- Lê Xuân Cường
- [...]
- Nguyễn Ngọc Hậu
Hạ tầng giao thông thực sự cần thiết để kết nối giao thông đô thị, đồng thời là động lực thúc đẩy phát triển kinh tế xã hội. Tuy nhiên khi phát triển hạ tầng giao thông để kết nối không gian đô thị giữa bờ trái và bờ phải người ta thường sử dụng đường dẫn kết hợp cầu vượt sông. Các hạ tầng giao thông này đã chiếm một phần không gian thoát lũ của sô...
Nghiên cứu đánh giá tác động của ngập lụt tỉnh Tiền Giang
Article
Full-text available
- Phạm Hồ Quốc Tuấn
- Nguyen Bach Tung
- Doan Quang Tri
- [...]
- Nguyễn Văn Nhật
Nghiên cứu đã thiết lập bộ công cụ mô hình MIKE FLOOD kết nối MIKE 11 và MIKE 21 với bộ số liệu mặt cắt, công trình cập nhật và hiệu chỉnh, kiểm định cho mùa lũ các năm 2000, 2011 và 2018. Kết quả tính toán mô phỏng cho thấy kết quả tương quan tốt giữa số liệu tính toán và thực đo, từ đó bộ mô hình được sử dụng để mô phỏng và đánh giá ngập lụt trên...
Apply MIKE models to study the impacts of climate change on flooding and design adaptation measures in Can Tho City in the Vietnamese Mekong Delta.
Article
Full-text available
- B Q Ho
- T Nguyen
- Kh Vu
- [...]
- N Huynh
Can Tho City in the Mekong Delta usually has pluvial and fluvial floods every year. The situation will get worst in the future under climate change. This study aims (i) to apply the MIKE 11, MIKE 21, and MIKE FLOOD model to simulate the impact of climate change scenarios on flooding in Can Tho city (ii) to suggest climate change adaptation measures...
Got a technical question?
Get high-quality answers from experts.
Top contributors to discussions in this field
Demetris Koutsoyiannis
Linh Nguyen Van
Christopher Gomez
Himanshu Tyagi
Mohamed Azab
Join ResearchGate to find the people and research you need to help your work
- 25+ million members
- 160+ million publication pages
- 2.3+ billion citations
or
- Join for free
- LoginEmail Tip: Most researchers use their institutional email address as their ResearchGate login
PasswordForgot password?
Keep me logged inor
Continue with Google
Welcome back! Please log in.
Email · HintTip: Most researchers use their institutional email address as their ResearchGate login
PasswordForgot password?
Keep me logged in
or
Continue with Google
No account? Sign up
- Badges
- Science topic
- Similar topics
- Analytical Chemistry
- Column