Have you done Comsol Simulation of a SAW device?

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View

How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

22 February 2021 5,408 1 View

Ali Zare

Which type of sawing machine?

What kind of modeling?(1D-2D OR 3D),unsteady or steadt state

What kind of answer you're looking for?

Ashish Kumar Singh

SAW stands for surface acoustic wave. COMSOL has two model library examples for modelling those. Links are below:

http://www.comsol.com/model/two-port-piezoelectric-saw-device-19155

http://www.comsol.com/model/surface-acoustic-wave-gas-sensor-2129

Vishal Dhagat

Surface Acoustic Wave Modeling and Simulation is well underway. Thanks for all responses, Hoping to publish work soon.

Update: I have now a working COMSOL model of my SAW device.

Maina Francis

please share your model for reference. i am working on vibrations on Furrows

Hongsheng Xu

Hello, i am also working on SAW simulation using COMSOL. I have succesfully done 2D simulations of SAW device, but when i did 3D simulation, i found that the frequency is not correct, but the mode shapes are correct. Does anyone know whats the problem?

My comsol file is attached below. Thanks!

Rajat Srivastava

Vishal Dhagat Sir, please share your working model on SAW. It will be very helpful for me.