Has anyone worked on the modeling of boundary lubrication regime in the presence of nanoparticles as additives between steel-steel contact?
This phenomenon is in effect at Mechanical Face Seals working in Oil and thrust bearings.
Contact for further details.
Search author:Asadauskas and nanoparticles. The top result is "Tribological effects of Cu, Fe and Zn nano-particles, suspended in mineral and bio-based oils " Lubrication Science Volume 28, Issue 3, 1 April 2016, Pages 157-176
This is a Miocene limestone thin section and the specimens is probably belongs to the larger benthic foraminiferal group.
05 February 2024 3,709 1 View
This is from Miocene limestone and we are thinking this is a section of larger foraminifera.
05 February 2024 9,164 1 View
ASTM 4170 indicates the usage of 9 balls in a thrust bearings and the bearing ball diameter is 7.1mm. However, is it wrong if we use a 11 nos. ball thrust bearing and 6.5mm ball diameter? other...
06 November 2023 6,013 0 View
If extracted viral RNA contains 2.5% isopropyl acetate, would it be acting as PCR inhibitor?
20 October 2020 3,229 3 View
Tribology of lithium.
09 December 2019 554 2 View
I am trying to find out a suitable technique to calculate the lipid concentration of LUVs. In between the preparation process I loose a portion of the lipid. So want to know how to calculate the...
01 May 2019 7,559 4 View
I had a mineral oil of 460cSt (containing sulphur and phosphorus), after addition of nanparticles (carbon nano tubes and graphene) the viscosity decreased significantly. literatures says that the...
16 August 2018 6,607 1 View
Two oils were tested. Mineral oil and a vegetable oil. The coefficient of friction of the vegetable was found to be lesser than mineral oil but the roughness was higher in vegetable oil.
02 November 2017 7,457 2 View
Case I : An experiment was conducted using some additives. The additives formed a protective layer on the steel surfaces which reduced the roughness and hence h/Ra increased. Case II: When the...
04 July 2016 2,013 6 View
Mechanical properties influencing coefficnet of friction.
21 June 2016 1,483 2 View
What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?
04 August 2024 1,078 1 View
N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.
30 July 2024 7,233 4 View
I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.
29 July 2024 6,115 0 View
Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...
25 July 2024 8,108 0 View
Dear all, I gave 116 respondents 18 translated sentences and asked them to indicate their levels of acceptance of these translations on a five-point scale. Some translations result from strategies...
24 July 2024 8,245 5 View
Hello, I'm planning a shell exchanging experiment with two marine, hermit crab species inside of a tank. I only have one tank available for this experiment. I plan on running 30-40 shell...
20 July 2024 5,676 3 View
Hello everyone, I am currently working on a project where I aim to analyze color preferences in data visualizations across participants from three different countries. The dependent variable in...
19 July 2024 4,178 2 View
Hello, I would like to ask which is the best terminology to use for describing a negative control in an experiment (drug testing in-vitro, viral infection): NC (negative control) or NTC? Thank you...
18 July 2024 4,183 2 View
If I want to invent my own hypothesis testing method, where should I get started ?
15 July 2024 5,376 5 View
For my practical project at Uni, I am researching blue-green algae in a freshwater lake. I have three locations around the lake and am testing the water for phosphates, pH, and temperature. I am...
30 June 2024 4,264 3 View