Aqueous two phase separation (ATPS) - Which are the relevant criterions to decide whether the product should be in the upper or lower phase?

Helllo, if I want to set up a process which wants to manufacture molecular Antibodies and I want to separte them from cell debris, DNA etc. as a first separation step, are there any general...

20 September 2019 9,051 3 View

What are the biggest structural differences between human and mice antibodies with respect to domains, fab, fc, variable constant chain, hinge region?

Hello, what would be characteristical structural/chemical/modificational differences between human and mice antibodies for all or specifif Ig classes? Best, Dennis

12 September 2019 1,769 3 View

What are the biggest structural differences between human and mice antibodies with respect to domains, fab, fc, variable constant chain, hinge region?

Hello, what would be characteristical structural/chemical/modificational differences between human and mice antibodies for all or specifif Ig classes? Best, Dennis

08 September 2019 8,818 3 View

Aqueous two phase separation (ATPS) - Which are the relevant criterions to decide whether the product should be in the upper or lower phase?

Helllo, if I want to set up a process which wants to manufacture molecular Antibodies and I want to separte them from cell debris, DNA etc. as a first separation step, are there any general...

08 September 2019 9,186 3 View

Does anyone has fouling factors heat exchange design for lignin solutions or the aqueous/oil phase after hydrothermal liquefactions or other treatmen.

for u-bundle heat exchanger oder any other heat exchange device

21 May 2017 3,419 3 View

Does anyone have heat transfer coefficients between lignin solutions and the aqueous/oil phase after hydrothermal liquefaction or other hyd. treatment

with a U bundled heat exchanger or any other heat exchange device

21 May 2017 4,176 1 View

How would you calculate the heat capacity of a 1% wt KOH and 13% Ligin solution? I have the cps of dry KOH and Ligin, can I sum up by relative weight?

The Temperature of KOH and Ligin should be room Temperatur around 298,15 K, Water has a fraction with room temperature and a fraction around 353,15 K, but perhaps its ok to consider all components...

06 May 2017 6,661 3 View

Does anyone have heat transfer coefficients between lignin solutions and the aqueous/oil phase after hydrothermal liquefaction or other hyd. treatment

with a U bundled heat exchanger or any other heat exchange device

04 May 2017 6,940 1 View

How would you calculate the heat capacity of a 1% wt KOH and 13% Ligin solution? I have the cps of dry KOH and Ligin, can I sum up by relative weight?

The Temperature of KOH and Ligin should be room Temperatur around 298,15 K, Water has a fraction with room temperature and a fraction around 353,15 K, but perhaps its ok to consider all components...

04 May 2017 6,128 4 View

Has anyone measured the viscosity of Lignin / Water and catalysts such as Kaliumhydroxide solutions?

04 May 2017 1,524 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View