I am trying to simulate phase change of refrigerant inside pipe extracting heat from panel in comsol. Can anyone help with how to simulate this?

My model is a rectangular multi layered structure under which refrigerant flows through cylindrical pipes. A heat flux of 600W/m2 applied on panel and internal forced convection is used for...

20 January 2021 9,478 1 View

Why does the ghost atoms gives error in NICS calculation with wb97xd in gaussian09 ?

In a trial, I am trying to calculate NICS (0 and 1) values for benzene ring using gaussian09. I have placed the ghost atoms at the center, 1A, and 2A above the rings. On using the method/basis...

19 January 2021 3,188 3 View

Rejected manuscript for journal publish after 1st revision, what needs to be done next?

Hello, My manuscript has been rejected by the editor and reviewers even after the 1st revision. Though I tend to disagree some of the points raised, assume I can't request for another revision...

28 December 2020 6,062 3 View

Acetylene reduction assay procedure?

Do anyone have the detailed step wise procedure(practical) to do the acetylene reduction assay? Or if anyone can let me know in which institute can i analyse my samples in India?

28 December 2020 6,717 2 View

How to capture UV- fluorescence from a substance using a camera?

I have a liquid that glows when UV light is shined. However, when I use my phone camera I can't see the glow, I just see a violet hue. What is the best way of capturing the fluorescence-glow from...

02 October 2020 8,664 3 View

What is the actual basis on which amount of Perovskites materials are to be taken?

In some discussion people took 112 mg of MAI and 461 mg of PbI2 in 1 mL DMF and some took 461mg of PbI2 too but 159mg of MAI there are many other authors took different amount of these materials...

17 September 2020 9,998 3 View

Forums to get online survey responses?

For my journal publish, I have been asked to increase the sample size by 200. I have been individually contacting more than 1000 Linkedin contacts and posted in all professional groups. But have...

04 September 2020 2,564 5 View

Derivation of Rice and Tracey equation???

12 July 2020 6,555 1 View

Can anyone suggest me where to get a low cost 2D Heterostructure Transfer System?

Except the 2D transfer system sold by HQ Graphene

09 July 2020 3,276 4 View

What digital technologies are more helpful to sustain Agriculture?

With the global Corona Pandemic situation, it looks to be inevitable to move towards digital technologies to get adapted in various farming sectors. With the advent of IoT, Robotics, Data Science,...

10 May 2020 8,570 5 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View