What are technical problems working with HCT116 colon cancer cell line ? how is it maintained and cultured to study the anticancer effects of a drug?

Technical problems working with HCT116 compared with other cell line Caco-2 and HT29

07 January 2021 2,067 3 View

How to cite a reference for a literature review?

Someone confuse me, he said that when you have some information you want to use it from reference say X, and the reference X inspired this information from reference say Y, then so, I should cite...

21 September 2020 8,630 3 View

How is the coronavirus affecting your research and teaching?

The coronavirus is affecting our lives in many ways, including conducting field trips and laboratory experiments in research and teaching. In-person classes are now being moved to online, which is...

16 March 2020 9,288 6 View

How can I extract the intensity of electric field maps (E^2 or H^2) in the CST Microwave Studio?

We are looking for a method to extract the power of electric field from the CST Microwave studio simulation. Thanks

14 October 2019 5,769 1 View

How can I determine a metastable phase?

Dear colleagues, Recently, I found a new metastable phase which has not been reported so far. The approximate phase constitution for this metastable phase has been measured by the EDS technique....

17 March 2019 9,725 3 View

In gromacs MD simulation , I run my file with nsteps = 10000000; 2*10000000=20000ps (20ns). Is this correct for 20ns or it should be 10ns ????

I wants to know what's the relationship between nsteps ,ps,ns .How can I calculated exact time for simulation.?????

07 February 2019 8,118 5 View

How can I dry glycerol on nitrocellulose membrane without damaging antibody?

20 April 2017 793 1 View

What is the best way to link Rhodamine 110 dye with Chitosan polymer?

I want to link Rhodamine 110 dye with chitosan polymer and use it for coating over inoganic nanomaterials with amine functional groups through EDC/NHS chemistry. What is the best way to graft...

04 May 2016 4,691 2 View

When should I block my nc membrane with BSA?

I am creating a sample test of a LFA on a nitrocellulose membrane. I have seen some contradicting protocols regarding blocking the membrane so far. Some suggest doing it before I spot the membrane...

16 April 2016 5,456 2 View

At what setting should I sonicate my carbon nanoparticles?

I will be using the M220 or E210 Covaris sonicator. Any insight would be greatly appreciated! I will be sonicating 1 mg of carbon nanoparticles in 0.1 mL of water and then later with added borate...

14 April 2016 245 3 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Is it necessary to report effect size (ES) in statistics of biomedical research given that we already report p values routinely?

Pls share your thoughts

01 March 2021 7,330 4 View

Which reagent is best among 'Dimethylglyoxime" and "Dithiothreitol" for spectroscopic determination of Nickel ?

What I think is Dithiothreitol. As it is water-soluble and does not form a precipitate. But, the thing is it contains sulphur which is quite hazardous to aquatic animals.

01 March 2021 8,374 4 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View