Force driven load deflection response in apdl?

07 July 2018 0 9K Report

How to get a post buckling deflection curve using force driven analysis in apdl. The graph stops short and the run is terminated when the load reaches ultimate load or when the von mises stress criterion is reached in which case the simulation is unable to reproduce the descending branch of load deflection curve

#apdl #loaddeflection #fea #steel #errors

Badges
Science topic

More Inaam Qazi's questions See All

Excessive distortion issue while doing non linear static analysis?

I am doing a non linear analysis incorporating material and geometric non linearity. I apply a non linear ststic load higher than the linear eigen buckling load. the analysis terminates on account...

03 April 2019 3,039 3 View

Differences in Load controlled and displacement controlled conditions ?

Why is that load controlled and displacement controlled boundary conditions give different results for same meshing and boundary restraints ? I specify time at the end of load step as 1 and no of...

01 February 2019 6,263 7 View

Selection of node from a subset of nodes corresponding to maximum displacement in one direction?

How to select a node from a set of selected nodes and get the node number corresponding to maximum value of say y displacement. It should also take the mod (for selection of maximum negative...

31 December 2018 5,146 1 View

How to do linear combination of eigen modes corresponding to 2 different loadings in APDL?

If I apply 2 different types of loading and I get different eigen modes for different loading types, how do I combine them in a linear fashion in APDL.Tutorial would be nice.I have used upgeom...

10 November 2018 3,707 0 View

How to get APDL to read a column from a matrix element by element , so that I can operate on each elements ?

I have made a matrix of areas 76 *5 which contain areas in first column , centroidal coordinates in the 2,3,4 columns.I want to read the first column element by element so that I can make...

07 August 2018 3,173 6 View

How to SELECT THE keypoints associated with area numbers in APDL?

I have selected a subset of areas by ASEL,S,LOC,Y,0 APLOT With the selected areas I have counted them via *GET,A,AREA,,COUNT then I have defined an array via *DIM,B,ARRAY,1,AREA This creates an...

06 July 2018 8,320 4 View

Doubts in representative finite element modelling?

I have attached a picture which shows 2 co axial tubes being compressed by heavy end plates. But the reduced modelling technique does not make much sense to me . IF someone could help in...

03 April 2018 8,962 3 View

Modelling issues with flange buckling of I beams ?

I am doing non linear buckling analysis to determine the buckling co efficient of flange buckling of I beam. For doing eigen value buckling analysis , and from there I do non linear analysis to...

02 March 2018 4,655 1 View

How to add residual stress distribution ?

I am modelling an I-beam with geometric imperfection and residual stress distribution for non-linear analysis. How can I add residual stress distribution which is varying in nature. Please find...

02 March 2018 6,530 7 View

Validation issues on load deflection curve of stiffened plate girder through numerical analysis?

1) I am doing validation of non linear analysis of stiffened steel plate girder. When I use 1500kN the analysis converges . If I use 1800kN the analysis terminates at a substep and if I see the...

01 February 2018 4,927 1 View

Dear all, I was wondering if anyone knows whether MGLtools and Autodock can run on Mac OS?

I have tried to download the 64-bit version of MGLtools however, as many times as I have downloaded and uninstall the programs, an error arises that the app needs to be updated. Thank you.

03 March 2021 5,997 2 View

I got 02 moderator values defining Johnson-Neyman significance regions. Is it an error?

Hi everyone, I am conducting research for my Master's thesis. I am using PROCESS by Johnson-Neyman to analyze my Moderator model. I test the relationship between Public Service Motivation and...

03 March 2021 2,350 2 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Do I need to strip the PVDF membrane before staining it with colloidal gold?

Dear Colleagues, After running Western blot on PVDF membrane and detection using ECL, I would like to stain my PVDF with colloidal gold to be able to allign the ECL image with total proteins on...

02 March 2021 7,829 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

PACYC PCR not working after several attempts. Would anyone have any suggestions?

So, I have been trying to run a pACYC PCR which will be used later on for a Gibson Assembly. However the PCR is not working. I have already tried gradient PCR and changing extension time; however...

02 March 2021 1,146 2 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View