07 May 2019 1 5K Report

while working on distortion simulation of SLM process in Simufact additive i figure out that there is no way to relate the scanning pattern and laser power and laser scanning speed in the software package , how can i incorporate these among the simufact additive simulation?

More Saad Waqar's questions See All
How to avoid polypyrrole deposit on counter electrode?

Hi all, Currently, I electrodeposited polypyrrole on carbon electrode but I got some problem when polypyrrole also deposited on the surface of the counter electrode. The concentration of pyrrole...

05 February 2021 2,103 3 View

How to Extract DNA from dried rhizomes, wood, galls etc. stored for a long time?

Dear Respectable Scientists, I have been trying to extract DNA from above mentioned sources using different CTAB/SDS Buffer Compositions and purifying agents but I am not able to extract DNA from...

12 January 2021 5,899 8 View

How to carry out Fisher's Exact Test in SPSS for multiple Response Dataset?

I have a dataset including Categorical variables and involves multiple response variable. 20% of the cells in cross tab has less than 5 frequencies and hence I cannot carry out a Chi-square Test....

26 December 2020 4,180 3 View

Can cosine of solar zenith angle be negative?

I am trying to find the cosine of sun elevation angle on slope terrain, I found the values between -0.9 to 0.9. Should the value be set to 0 - 0.9 or the negative value acceptable?

24 December 2020 4,027 4 View

**CLOSED** Behavioral changes due to Covid-19?

Hello fellow researchers around the globe :) Happy Holidays!! We are conducting a survey on understanding how device usage during everyday life has developed amid the Covid-19...

21 December 2020 5,363 4 View

Does the Chinese navigation satellite system (Beidou) become global or still regional?

I know that this system was regional before, thus covering specific areas not alla the global

09 December 2020 3,343 3 View

Interpretation of Probit in Propensity Score Matching (PSM)?

Is it necessary to interpret the results of Probit while using Propensity Score Matching (PSM) for impact evaluation?

30 November 2020 8,796 1 View

Exergy destruction mathematical calculation in kW?

somebody, please elaborate on how to calculate exergy destruction in kW units. from Aspen HYSYS I found mass exergy with kJ/kg unit and i don't know how to calculate it by using Aspen HYSYS and if...

25 November 2020 2,675 3 View

How to coat oleic acid on fe3o4 nanoparticles and yo confirm visually?

I made iron oxide nanoparticles via co-precipitation method and obtained a brown colour slurry with neutral pH and I did ex situ coating of oleic acid on nanoparticles and washed it with ethanol...

10 November 2020 5,911 4 View

How to get labels from synthetic dataset?

I have synthetic dataset, but I don't how to get labels from this dataset. Need helpful suggestions and advices. Thanks a lot in advance.

10 November 2020 5,167 3 View

Similar questions and discussions
fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Which is the most convenient manufacturing software for Additive Manufacturing?

Which tools can be used to generate machine codes for additive manufacturing?

02 March 2021 7,220 2 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close