I've been trying to export the mesh file of my newly generated mesh from MIKE 21. But it's not going through. The error message claims "Invalid mesh specification." What could be wrong?
I want to know more about Uranium ore deposits in world.
11 August 2024 6,718 0 View
I want to know more about diamond ore deposits in world.
11 August 2024 2,165 1 View
If Banks do not provide credit facility, what are the options available for FPOs and impact on producer’s income?
10 August 2024 8,197 5 View
We assume that the difference is huge and that it is not possible to compare the two spaces. The R^4 mathematical space considers time as an external controller and the space itself is immobile in...
10 August 2024 6,676 14 View
What are a “Farmers Producer Organization” (FPO) and its essential features?
10 August 2024 475 5 View
I used eye tracking to examine how participants from two different populations (A and B) react to an image. Participants in population A exhibit larger pupil sizes over time, but they also have...
10 August 2024 3,226 0 View
I have been doing the m6A dot blot for a while with no improvement, I am extracting the RNA, and I can see the dots although the three biological replicas give a different reading on the memberan...
10 August 2024 8,537 5 View
How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?
09 August 2024 3,286 2 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,829 4 View
I am modelling CFS Sheath wall in abaqus and i am applying the 100 mm displacement but i am getting high reach force close to 150 kN but i need it till 50kN. I have used mesh independent fastner...
27 June 2024 4,212 2 View
For the article, I need some references for the subject of checking the convergence of the temperature field parameter for the SPH part in Abacus, and I want to study this case with a few meshes...
13 June 2024 2,503 0 View
Hello. I am trying to do contact-separation mode TENG. I have been following , and I am suffering to calculate the Open circuit voltage (Voc). I made geometry and set the materials setting all...
26 May 2024 2,644 0 View
Hi all, Here’s a simple but still very important (I think!) question regarding the philosophy of mesh overlap in open ventral hernia… I’m keen to clarify the concept of transverse diameter mesh...
25 May 2024 4,743 2 View
Hello I am trying to simulate 2dof cylinder for VIV analysis and I used an FDM method but the cd and cl values i got are so high and the damping is not coming into picture i tried and modified the...
17 April 2024 4,597 0 View
Dear Sir/ Ma'am When I am considering the human model with an antenna for simulation in CST then it is reflecting an error as "Time domain solver does not support mesh size > 2 billion mesh...
29 March 2024 8,204 1 View
When I ran the HD Simulation on Mike Zero, I got an abnormal completion error stating that "CheckLicense: Node Limitations exceeded." Has anyone faced this problem in the past? How can I solve the...
27 March 2024 8,867 2 View
1.Fixed boundary condition at both end of the pipe elbow. 2.Pressure applied is 30 Mpa. 3.Hex ,sweep mesh applied.
18 March 2024 5,934 2 View
I am currently conducting an analysis on a wind turbine and I am trying to input periodic boundary conditions in the mesh and it keeps showing me the same error which is the meshing algorithm...
13 March 2024 9,826 0 View
Greetings to all.. I am working on CFD analysis of a double pass solar air heater. The geometry is as shown in the attached file. It consists a rectangular duct with an absorber plate within the...
12 March 2024 6,153 0 View