Microchannel's most important applications?

I am looking for the microchannel's most important applications between: - Micro-electronic Thermal Management - Solar Collectors - Space Machines Cooling - Drilling Devices and etc ...

02 March 2018 2,120 7 View

Slip flow in Microchannel?

Is there non-slip condition in microchannels? The literature show that to simulate fluid flow in microchannel, one should consider slip flow. what is the relation between slip flow and boundary...

02 March 2018 8,704 7 View

Which country for higher educational program?

I am looking for a suitable PhD program in Mechanical Engineering (Energy Conversion) with financial aids. Which country is the best option and why? Regarding community, research opportunities,...

02 March 2018 2,332 22 View

Which programming language to simulate heat transfer and fluid flow?

Which programming language is the best to use in CFD? FORTRAN, MATLAB or any other? Is there difference between the performance of these codes and applications such as OpenFOAM?

01 February 2018 8,952 33 View

Nanofluids in OpenFoam?

The simulation of the nanofluids flow as two phase flow is possible in OpenFOAM? Is there any specific solver?

31 December 2017 3,637 3 View

OpenFOAM in Windows10?

Has anyone experience with OpenFOAM in Windows 10? What about its solvers, run time and the other features?

31 December 2017 5,288 5 View

Air cooler test rig?

what are the key elements of a air cooler test rig?

31 December 2016 4,778 0 View

Organic Waste to Energy?

11 December 2016 7,396 14 View

The modeling of nanofluids flow with Lattice-Boltzmann method?

Do you know about the ability of Lattice-Boltzmann method to model nanofluids flow in some complex geometries? Thanks all

09 October 2016 9,280 9 View

The best software package to model a plate heat exchanger?

Hi What is the best software package to model a plate heat exchanger?

07 August 2015 9,071 5 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

Where can I find life cycle inventory or assessment of non woven materials?

Dear network, I am looking for the LCA or LCI or at least the energy balances of the non woven fabrics process for my master project, in specific for natural fibers, yet I have found...

02 March 2021 9,662 1 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View