Why can I not use mathematic expression with "j" ( complex number) in MathCAD ?

10 November 2018 4,907 1 View

Which is type of "selective switch valve" for microfluidic application ?

Hi all experienced scientists I am doing a sensing measurement based on microfluidic device. As I sketched in my attached file, I have one buffer solution (PBS) and nearly 8 bacteria samples....

07 August 2018 7,478 0 View

Is N-methacryloyl l-histidine methylester (MAH) still available ?

Hi all scientist I am doing my research work related to polymer, so I need to use N-methacryloyl l-histidine methylester (MAH) chemical. Unfortunately, I can not find any supplier for it. Does...

05 June 2018 8,348 0 View

Why the MIP layer was cracked under UV-exposing ?

Hi everyone I am doing with MIP technique now and, I tried to following to attached paper for MIP chemicals and protocols. To practice MIP, I tried to coat a thin layer of polymer solution on a...

02 March 2018 4,816 0 View

How to double-side mask aligment for 1 inch wafer ?

Hi all I need to fabricate my device on quartz wafer with 1 inch in diameter and both electrodes on top and bottom side must be high concentric. So I need do this work on double-side mask...

09 October 2017 181 0 View

How to define the Quartz material in ANSYS ?

Hi Scientists I gonna do a simulation for my device ( with Quartz material, AT-cut type), using ANSYS. But I dont know how to create or define this material in ANSYS ? Hence, I post this my...

09 October 2017 5,644 0 View

Implementation of PDE equation in COMSOL ?

08 September 2017 6,808 0 View

Can I apply Matthieu equation for the rectangular plate?

Hi Scientist I am doing a design my sensor based on the rectangular quartz plate. I reviewed some paper about introduced Mathieu equation for analysing the vibration of the plate, but all plate in...

08 September 2017 3,890 0 View

Which type of OTA have "negative transconductance " ?

08 September 2017 7,803 11 View

Help me to clear problem in frequency domain (COMSOL) ?

Hi all I have a problem with eigenfrequency and frequency domain, I hope someone can help me to clear I using PDE Coefficient form, and solve my problem in 2D, with independent variable (u) =...

08 September 2017 202 1 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How to replicate the well conditions of a crystal hit with 20%(w/v) isopropanol?

I had a crystal hit in a well with 0.1M HEPEs pH 7.5, 10%(w/v) PEG 4000, and 20%(w/v) isopropanol. Why is isopropanol in w/v here if it's just solvent? How do I recreate this well condition?

25 February 2021 9,761 1 View

How can I selectively dry etch Ti on a polymer substrate?

24 February 2021 5,378 1 View

How to search for crystal structure for material with atomic position labelled?

I am using the crystallographic open database and materials project to search for cif file but the exact structure is not mentioned or how can I deduce that the given structure and atomic position...

23 February 2021 6,723 2 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

Build an orthogonal box in ASE?

Hello, I was wondering the best way to build an orthogonal box filled with a defined crystal structure in ASE. I know it could be easily done in LAMMPS, but I guess it is also doable in ASE. The...

21 February 2021 5,899 4 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View