Why can I not use mathematic expression with "j" ( complex number) in MathCAD ?

10 November 2018 4,907 1 View

Which is type of "selective switch valve" for microfluidic application ?

Hi all experienced scientists I am doing a sensing measurement based on microfluidic device. As I sketched in my attached file, I have one buffer solution (PBS) and nearly 8 bacteria samples....

07 August 2018 7,478 0 View

Why the MIP layer was cracked under UV-exposing ?

Hi everyone I am doing with MIP technique now and, I tried to following to attached paper for MIP chemicals and protocols. To practice MIP, I tried to coat a thin layer of polymer solution on a...

02 March 2018 4,816 0 View

Etching AT-cut type of Quartz Wafer ?

Hi all scientists I am gonna do a etching process with AT-cut Quartz wafer for my QCM sensor. My plate thickness is 160um, and its shape is 200 x 200 mm. Etching area will be circular shape with...

11 December 2017 9,409 0 View

How to double-side mask aligment for 1 inch wafer ?

Hi all I need to fabricate my device on quartz wafer with 1 inch in diameter and both electrodes on top and bottom side must be high concentric. So I need do this work on double-side mask...

09 October 2017 181 0 View

How to define the Quartz material in ANSYS ?

Hi Scientists I gonna do a simulation for my device ( with Quartz material, AT-cut type), using ANSYS. But I dont know how to create or define this material in ANSYS ? Hence, I post this my...

09 October 2017 5,644 0 View

Implementation of PDE equation in COMSOL ?

08 September 2017 6,808 0 View

Can I apply Matthieu equation for the rectangular plate?

Hi Scientist I am doing a design my sensor based on the rectangular quartz plate. I reviewed some paper about introduced Mathieu equation for analysing the vibration of the plate, but all plate in...

08 September 2017 3,890 0 View

Which type of OTA have "negative transconductance " ?

08 September 2017 7,803 11 View

Help me to clear problem in frequency domain (COMSOL) ?

Hi all I have a problem with eigenfrequency and frequency domain, I hope someone can help me to clear I using PDE Coefficient form, and solve my problem in 2D, with independent variable (u) =...

08 September 2017 202 1 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

How do I determine the degree of polymerization of PEG 400 based on NMR integration?

Hello, I am working on the photocatalytic degradation of PEG 400. I would like to know if it's possible to determine the degree on polymerization based on NMR integration, or by the MW of the...

02 March 2021 6,186 3 View

How to polymerize TEOS?

I want to polymerize TEOS on a surface. I know that NH4OH is a preferred catalyst and an alcoholic solvent should be used .But I can not find certain amounts of each material to use. Does any one...

02 March 2021 1,404 6 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

How to reduce residual stresses in MD simulation?

I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...

24 February 2021 8,105 3 View

How to identify what type of fillers are in a polymer?

Hello everyone, I have some PHAs blended with fillers and nucleating agents, yet I don't know what kind of fillers or nucleating agents. The producer has shut down and there's no way to get in...

24 February 2021 1,356 8 View

How can I selectively dry etch Ti on a polymer substrate?

24 February 2021 5,378 1 View

How to do a surface treatment of uncoated TiO2 with polymer?

Basically, I would like to know how to treat or coat on the uncoated bare TiO2 (Ti-OH rich) surface with polymer which has anchoring groups in the polymer structure like trimethoxygroups. What is...

21 February 2021 4,657 6 View