Does anyone knows how Etabs Shell Layered Element works with the total section modulus(we provide different material properties in the thickness direction). How the forces are captured/attracted in the overall shell element?
i cant get what you want can you explain more to help you
my regards
i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).
03 March 2021 7,100 1 View
Hello everyone! I am interested in the topic of solar energy production forecasting for a ground-mounted PV system of more than 100MW capacity. Can anyone please suggest what are the main data...
08 February 2021 6,834 5 View
I was curious to know why we only use sand for covering the AC cables inside the trenches and instead of having good isolation why these cables are covered. Why is there a problem in the trenches...
13 January 2021 6,008 3 View
In Terrset, an error encountered in executing Spatial Decision Modeller (MCE). During execution or run the MCE a massage come on the screen that reflects "Your columns and rows are not same" , I...
07 December 2020 1,542 1 View
Hello everybody, Hope you all are doing fine during this difficult time. I am trying to culture mouse oviductal epithelial cells but, the problem is when I culture them there is a mixture of...
31 October 2020 2,640 4 View
I have already been read many articles and found some methods but those are not cleared to me. Can you please suggest me how to generate different LST map of each land classes using ArcGIS? Or...
25 October 2020 5,978 5 View
10 October 2020 7,411 9 View
I had estimated the Land surface Temperature and Normalised Difference Vegetation Index, the result shows they have positive relation both increases in lower south part areas and higher in upper...
11 September 2020 6,021 4 View
Second Law of Thermodynamics states that as usable energy is lost, chaos increases - and that progression towards disorder can never be reversed.
01 September 2020 2,528 37 View
I am trying to CG relax a amorphous GeSe system with B3LYP and single K-point (gamma). Even though I have a 250 atom model, the calculations seem to be extremely slow. Is there a way to speed up...
23 August 2020 8,848 4 View
Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...
01 March 2021 9,537 2 View
Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...
24 February 2021 8,856 3 View
In Ansys APDL, We are trying to validate our shell model for nonlinear buckling analysis considering the initial imperfection (as given by Ahmed et. al.) We have attached our results as attached....
13 February 2021 9,200 5 View
Unlike shell elements, solid elements have three degrees of freedom. So how can I get the values of moments after I run the model/analysis on ANSYS / ABAQUS ?
21 January 2021 258 3 View
Two weeks ago I found a peculiar crab in the intertidal zone in SW Florida. when found, the crab was not utilizing a shell. It was similar shaped to porcelain crabs found in our area, but with...
17 January 2021 1,620 4 View
I executed simulation for a heat exchanger (shell and tube) . but i have a question that if i dont set the reference values and leave them as default values and as you know default temperature of...
10 January 2021 1,573 7 View
I am trying to select suitable element type (Solid or Shell) for impact analysis. I have tried with both solid and shell elements. The results are same for both element types up to certain impact...
08 January 2021 3,251 4 View
What is the difference between plane and shell elements in ANSYS? other than the fact that plane has 3 degrees of freedom and shell has 6 degrees of freedom?
28 December 2020 1,811 3 View
Is the stress throughout the thickness of the shell element the same? I learned that transverse shear stresses are accounted for in SHELL181 but I also read that stresses in shells along the...
28 December 2020 4,515 4 View
I am going to compare the result of the LTB derived by Matlab to Abaqus, I have done the Matlab analysis and I need to do it now with Abaqus, Can any body help me how can I do LTB in Abaqus either...
22 December 2020 803 1 View