This paper can be download free in the following 50 days (before August 29, 2020 ) by following the link: https://authors.elsevier.com/a/1bNS23jWfExfXq
My research topic is the corrosion of gray cast iron in methanol. EIS measurements were conducted at open circuit potentials (Eoc) using a sinusoidal signal with the amplitude of 10 mV from 100...
05 June 2024 6,891 2 View
I tried to synthesise different morphologies by adjusting the ratio of DMF to methanol. When the DMF and ethanol ratios were 9:1 and 7:3, the XRD images of the samples showed a diffraction peak...
08 April 2024 4,336 4 View
A very interesting phenomenon, for the existing high-entropy alloy design, the use of more elements are Fe, Ni, Co, Cr, Mn, Al, V, Ti, Zr, etc. However, the Mg element is rarely found in HEAs....
09 January 2024 2,599 4 View
I am a researcher at the Sun Yat-sen University, China. I am currently working on a research project that involves the simulation of pesticide concentrations in surface water using the SWAT model....
08 January 2024 1,237 0 View
I am wondering the possible influencing mechanisms of plasma on particles. Thanks for your attention : )
30 August 2023 5,799 0 View
How can I train an ANN using current raster data (population, precipitation, DEM, land use) and use this model to predict future land use based on upcoming raster data (population, precipitation,...
23 August 2023 6,487 1 View
The pH of my crystal PDB is 5.5, but I would like to perform a simulation under pH=7. I used PDB2PQR to change the protonation state, but because my structure contains a modified residue...
16 July 2023 523 0 View
I downloaded my pdb file from RCSB. Cuz I want to use amber tleap, I used pdb4amber to convert the PDB file. Then the error occurred: GLU_29 misses 4 heavy atom(s) ARG_102 misses 6 heavy...
18 June 2023 5,833 2 View
1. I am currently using a 532nm laser and NA = 0.6 objective lens for laser focusing, (the spot size of the laser outlet is 2mm, then expand the beam 4 times, and finally through several mirrors...
25 April 2023 7,181 11 View
Greetings, It is well known current TCM systems that detect tool breakage within one second. However, in high-speed machining, the workpiece surface integrity may be impaired. How to achieve the...
29 March 2023 9,472 2 View
i am unable to interpret why its increases in start as shown in figure
11 August 2024 2,179 1 View
I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.
09 August 2024 9,894 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...
05 August 2024 3,290 1 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...
28 July 2024 8,027 3 View
There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...
27 July 2024 7,168 2 View