Does the thickness of the coating affect the studied surface properties (anti-icing, super hydrophobicity, and anti-fouling)?

06 June 2018 0 8K Report

Badges
Science topic

More Rajiv .S's questions See All

What is the best way to find the postdoctoral position in Superhydrophobic field?

03 April 2019 387 1 View

What is the relationship between the weights of MWCNT:CNF and the thickness of the coating?

05 June 2018 4,942 0 View

Can anyone tell me the benefits of mixing two compounds(PTFE and PVDF) into the carbon family?

what is the main role of adding PTFE and PVDF into the carbon family like graphene, CNT, and CNF?

08 September 2016 7,825 0 View

How to measure the tensile strength of the prepared composite coatings?

I was totally confused to measure the tensile strength of the prepared CNF/PVDF composite coating.The thickness of the coating is 0.5 mm, is that nanoindentation method is convenient for this coating.

08 September 2016 7,347 2 View

what chemical reaction happen when mixing of CNT powder and PVDF into the organic solvent (Ethanol and DMF)?

I can used various solvents to get the uniform dispersion . But unfortunately I was totally confused to find which one is better after all I want to know why ethanol act as a good solvent when...

07 August 2016 3,400 3 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Can't spin-orbit coupling(SOC) be included in optical properties calculation in CASTEP?

I am currently using CASTEP version 2020. When I want to run optical properties calculations with spin-orbit coupling(SOC), I encounter the following error in a pop-up window before the job gets...

02 August 2024 2,890 0 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Can I proceed with Response Surface Methodology (RSM) with only one factor for further optimization?

I went for Plackett Burman Design for selecting the optimization factors of growth conditions for pesticide degradation. I started with 7 parameters. But, after the experiments and analysis, only...

29 July 2024 5,015 1 View

I did hirshfeld surface analysis for molecule but did not find red spot and interaction surface in energy frame work, is it ok for research article ?

In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?

28 July 2024 2,988 0 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View