For, SEM of aluminum alloy I am facing the difficulties to obtain grain boundaries in SEM images. Does an etchant play any role to obtain clear SEM image?
In which alloy you are trying?..
I suppose that Poultons etchant is proper depending on the alloy you want to observe in the SEM.
For seeing grain boundary, you must do polishing and etch then see in the SEM analysis.
Yes, absolutely, you need to etch
Can anyone tell me the tick species
13 July 2024 7,146 6 View
Hi all, I have a question regarding proper dilutions and conversions of my RNA. According to my protocol, my cDNA kit is optimized for 1ug of RNA and calls for this amount. I would like to...
07 July 2024 9,206 4 View
Hi all, I would like to know if it is possible to use Bovine Serum Albumin (BSA) in my blocking solution for immunofluorescence muscle fiber typing. The primary antibodies' host is mouse. The...
07 July 2024 7,967 3 View
Assessing the Feasibility of Vacation Homes and Vehicle Rentals in India In my article, "Assessing the Feasibility of Vacation Homes and Vehicle Rentals in India: Understanding Market Needs,...
03 July 2024 5,535 1 View
How the electron and hole pockets near the fermi level in the band structure affect the thermoelectric properties of the topological half-Heusler compound?
26 June 2024 2,933 0 View
There are two scenarios: The Impact Factor at the time an article is published. The Impact Factor after the journal updates its metrics annually based on performance. While being interviewed or...
25 June 2024 7,825 2 View
Why the IF of almost all journals declined so much? For the file download go to https://www.researchgate.net/post/JCR_Impact_Factor_2024-Factors_causes_decline_in_IF
21 June 2024 3,358 0 View
I tried to prepare aligned PLLA nanofibers by gap electrospinning method. But after the deposition, when I tried to measure its piezoelectric sensitivity, it actually did not exhibit any...
17 June 2024 9,763 0 View
I want to know the exact mechanism behind the motion of ions inside the polymer electrolytes.
13 June 2024 3,489 0 View
why uv is done and why photocatalytic measurement is done although both use uv radiation
09 June 2024 8,750 1 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...
07 August 2024 9,563 0 View
I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...
07 August 2024 5,177 3 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View