Does anyone know the experimental setup of gas sensor for impedance analysis using potentiostat/galvanostate?

More Sureshkumar Sundaravel's questions See All

How Can I calculate Gibbs Free Energy (ΔG)?

According to Adsorption Thermodynamics ΔG can be calculated from two equations ΔG = ΔH - TΔS --- (1) ΔG = RTln Kc ---- (2) The values of ΔH and ΔS are calculated from the slope and intercept of...

24 March 2018 5,886 9 View

How can Ce (concentration at equilibrium) for a particular temperature can have a multiple values In adsorption Isotherms?

Ce (concentration at equilibrium) is a single value for a particular parameter. For example activated carbon adsorption of methylene blue at 30 ◦C should have a single Ce (concentration at...

03 November 2017 8,821 4 View

How to find out microporous surface area and volume by DR-method from Nitrogen adsorption-desorption isotherm?

need informations regarding which particular P/P0 value or range of P/P0 values should be selected from isotherm and what tags should be applied for that

23 June 2016 4,061 5 View

Can anyone suggest the list of soil test conducted nearby to solid waste dump yard to identify the pollution level?

I plan to test soil pollution near by to the dump yard. For that what are all the list of tests essential to conduct for identifying the pollution level. Any standards are there for collecting and...

06 October 2015 2,043 14 View

How the DG penetration plays an important role in distribution system?

i am searching so many papers in this area some the researchers simply taken an assumption of 100% penetration and adding an distributed generation sources and minimizes the power losses to a very...

12 July 2015 1,554 1 View

How do I measure a gas in ppm when target gas flowing rate is 5sccm into the testing chamber?

I am doing research in gas sensor. using mass flow meter gas flowing rate in to the chamber (volume 500ml) is 5sccm. Now how do we know the ppm of gas?

12 May 2015 4,935 1 View

What is Methylene blue number? How it can be calculated? What is its significance in activated carbon?

Detailed procedure for detemination of Methylene blue number of Activated carbon is required?.

11 March 2015 3,845 3 View

What is the base case power loss for 118 bus distribution system?

i am working in distribution system side for comparing and analyse my results according to my objective function. i am having some problem with 118 bus system because according to my load flow...

20 February 2015 616 1 View

What is iodine number in terms of activated carbon? What is the significance of iodine number? How to find it?

In many paper, people are talking about Iodine number of activated carbon. What really Iodine number is? what is the significance of iodine number? how to find it?

27 January 2015 8,257 28 View

What is steam Activation?. How can it be achieved in order to get high surface area activated carbon?

I want to steam activate my activated carbon. We have electric tube furnace with 1 inlet. How it is possible with that?

13 January 2015 2,875 5 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

What is the best conditions for formation Magnetite ore deposits?

I want to know more about Magnetite deposits.

06 August 2024 1,066 0 View

What procedure should I follow for current controlled PPy film electrochemical deposition on ITO?

For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...

06 August 2024 3,176 0 View

How can I measure the thickness of thin film by Uv-Vis?

06 August 2024 7,810 3 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

Why is TLC not a form of partition chromatography?

Why is TLC not a form of partition chromatography and paper chromatography not a form of absorption chromatography?

03 August 2024 7,035 3 View

Muhammad Awais Khan

http://www.bio-logic.info/potentiostat-electrochemistry-ec-lab/instruments/

http://nuvant.com/products/potentiostat_galvanostat/?gclid=CPTEgPmwxL0CFfMQtAod6gIA5w

Sungjun Park

It depends on the circumstance of materials in experiment.

please let me know the object(goal) of your experiment.