Does anyone know if ucode2014 has any problems running modflow-nwt?

01 October 2022 0 9K Report

Sensitivities are not being calculated and the error indicates check process model.

Badges
Science topic

More P.T. Harte's questions See All

Can u please suggest me few books on green managment practices in SMEs?

I'm doing my research in smes. my research topic is "Green Management Practices and its impact on organizational performance in SME's in manufacturing sector". please suggest me some E-books, or...

03 February 2020 1,098 2 View

I am looking for resources/references investigating curiosity, playfulness and human health, especially as facilitated or inhibited by design?

I am developing a new course on this topic, so any well written articles or book chapters that explore the connections between curiosity and/or playing and human health (physical, psychological or...

28 February 2017 6,281 6 View

Do you have recent research related to the relationship of posture and pulmonary function?

I am a physical therapist preparing an "evidence-based" mind-body workshop called "The ABCs of Prevention and Fitness," Alignment, Breathing and Centering. I am looking for research establishing...

01 February 2017 7,513 4 View

Protocol for Annexin V PI flow cytometry?

I am tyring identify if my treated cells are dying through apoptosis or necrosis using flow. Can anyone suggest a good Annexin V/PI flow cytometry protocol? Ideally one that you have used and had...

05 August 2012 3,028 3 View

High sulfur count in ultrapure water

Anyone know or can recommend the sulfur filter for water system? Currently I am facing high sulfur count in our ultrapure water while test in ICPMS. Anybody face similar issue and is there any...

01 January 1970 272 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

AUX gas reading problem on QE with full MS and PRM method in one run?

Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...

06 August 2024 4,953 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

People weight in Oaxaca Blinder Decomposition on R?

Hello guys! Do you have experience running a Oaxaca-Blinder decomposition on R applying person weights. How do you suggest doing it? I have a variable PERWT which gives more information on how...

04 August 2024 6,033 0 View