Does anyone know how to create a clipped Voronoi diagram in MATLAB?

More Zhao lv's questions See All

Does anyone have experience with acceleration at the beginning of Abaqus/Explicit after results transfer from Abaqus/Implicit?

Hello Everyone I have a question about the results transfer from Abaqus/Implicit to Abaqus/Explicit. I performed a static calculation in Abaqus/Implicit and then I imported the results to...

07 August 2014 2,622 11 View

Can anyone help to establish the contact state after an importation from abaqus/Standard to abaqus/Explicit?

Hello everyone, I performenced a 4 point bending calculation in Abaqus/Standard, and then I imported the resultats to Abaqus/Explicit to do a dynamic job. Due to the difference of the contact...

07 August 2014 6,961 5 View

Is it possible to co-utilize XFEM and cohesive elements in Abaqus?

I have a question about the feasibility concerning the co-utilization of XFEM and cohesive elements in Abaqus. In fact, in the documentation, they did mention that XFEM could be simultaneously...

05 June 2014 3,090 10 View

Is there a cohesive zone model that is able to simulate the fast fracture propagation but with a quasi-static load?

I'm now trying to simulate the fast fracture on my thin brittle plate subjected to a quasi-static bending load. Is there a cohesive zone model that is able to simulate the fast fracture...

04 May 2014 846 0 View

Can anyone help with grain boundary simulated by cohesive surface in Abaqus?

I'm doing a simulation for a thin plate polycrystalline subjected in pure bending, and I consider the grain boundaries by the surface interaction using the cohesive surface behaviour in Abaqus....

04 May 2014 7,204 1 View

Does anyone have information about Abaqus XFEM based on the LEFM-initiation of crack?

Does anyone know about the Abaqus XFEM based on Linear Elastic Fracture Mechanics? The question is about how the fissure initiates under this finite element analysis framework. It's not like the...

03 April 2014 2,723 11 View

What is wrong with the STRESS values in UDMGINI user subroutine in Abaqus?

I wrote a subroutine UDMGINI to define a damage initiation criterion, but I found that the variables of stress were very strange. I kept track of stress (NTENS) using the state variables STATEV,...

03 April 2014 2,002 13 View

Can anyone help with simulation using XFEM in Abaqus?

I am trying to simulate brittle crack without initial crack using Abaqus XFEM. Specifically, I make a simulation of the 4 point bending (contact problem) on a very thin orthotropic plate...

02 March 2014 6,743 2 View

Construction of the grains' forms to be used in a Finite Element calculation?

In fact, I have a mechanical calculation on a piece consisting of grains whose grain boundaries are clearly visible. So I intend to build the grain boundaries. I have gotten an image taken by a...

01 February 2014 693 0 View

Damage model for initial anisotropic materials?

Does anyone know if there are some damage models that can be applicated on initial anisotropic materials?

01 February 2014 2,324 3 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

What precautions should be taken while handling S. aureus enterotoxin Type B in the lab?

I would like to understand potential safety concerns while handling SEB in the lab. Especially while working in animal house facility. Would like to know precautions for handling. Sigma MSDS...

07 August 2024 6,034 3 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,368 2 View

Help on understanding the implementation of Mori Tanaka method on MATLAB?

I am new to Micromechanics and having similar problem with understanding the implementation of the formula's. I would appreciate if anyone can guide me on how to go about getting a scalar value...

30 July 2024 969 0 View

CAD File of human's & rat's respiratory airways ?

Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...

29 July 2024 1,092 2 View

Do some Staphylococcus aureus strains have in vitro antimycobacterial activity ?

Some Staphylococcus aureus strains Inhibit the growth of Mycobacteria in Mueller Hinton Agar medium containing 10% OADC. Do some Staphylococcus aureus strains have in vitro antimycobacterial activity?

29 July 2024 10,023 2 View

Please, what is the memory consumption of the Matlab function quad tree decomposition procedure [S = qtdecomp(I)] with respect to the input set I?

27 July 2024 5,455 2 View

Has anyone looked into the stability of FEM methods on curved meshed?

Google scholar isn't giving me any results on this

27 July 2024 595 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Goutam Ghoshal

What do you mean by clipped voronoi. Do you need closed vor diagrams?

Nino Spinella

Http://www.mathworks.it/it/help/matlab/ref/voronoi.html

James F Peters

This is a good question. In addition to what has already been mentioned by @Nino Spinella, a good place to look for clipped Voronoi diagrams from a Matlab perspective is

M.S. Ebeida, S.A. Mitchell, Uniform random Voronoi meshes:

http://www.cs.sandia.gov/~samitch/papers/vor_final.pdf

Qhull (available in the current version of Matlab) can be used for computing Voronoi structures up to 4D (p. 4).

Zarghaam Rizvi

Zhao

did you find how to implement the clipped voronoi diagram?

If you succeed in implementing in MATLAB please share.