How to read a flow cytometry graph detailing cell cycle?

Hello everyone, When determining cells in different stages of the cell cycle, cells are stain for Brdu and Propidium Iodide. I understand how PI can be used to discriminate between G1 and S/G2...

18 February 2021 3,920 3 View

How to improve NHBE adhesion after subculture?

I'm trying to subculture NHBE cells from Lonza, however, the cells seem to not adhere to the new flasks after detachment. I've followed Lonza detachment protocol (2 mL/25 cm2 of Trypsin 0.05% and...

10 February 2021 196 1 View

How to perform Potential Surface Energy Exploration (PES) calculations?

I would like to receive help, as I am trying to make an analysis of the ethanol PES, but the calculations are always giving error. I use the conda-forge version of xtb (* xtb version 6.3.2...

04 January 2021 602 2 View

Asalam o alikum, Can anyone please help me in interpretation of XRD data?

Actually, I want to present the in table form (dcal , dexp, 2 thita, hkl) but don't know how to find these values from data.

28 December 2020 6,769 4 View

Is it need to test Cronbach's Alpha for extracted features from data?

As Cronbach's Alpha is usually used for test the reliability of measurements given by questionnaires, however, I wonder that whether I use this test for features extracted from behavioral data. I...

26 December 2020 9,602 2 View

Doping of r-GO?

if the percentage of doping Au into rGO is too small 1~10%, is it not enough to prevent restacking of r-GO in xrd results, rGO peak appeared at 22.2 and also the peaks of gold nanoparticles so...

21 December 2020 6,091 3 View

XRD peaks for gold nanoparticles ?

is the concentration of gold salt that were added will affect on the peaks appeared. i added a very little amount of gold salt to dope graphene oxide and not all the peaks that proved the...

17 December 2020 9,275 3 View

Calculation the Pump power needed in a pressurized flow system?

Hi all, I am design now a liquid high pressure flow system to be used up to 50 bar, and I am having some doubts concerning how I can estimate the pump power. Besides the pressure drop in the...

15 December 2020 8,411 1 View

Design of a membrane system to remove CO2 from a flue gas current?

Hi all, I am trying to design a membrane system to remove the CO2 from a flue gas current, and I am having difficulties in finding information. Does anyone have any technical information,...

15 December 2020 3,655 2 View

If someone has the pdf file of below mentioned reseach paper?

14 December 2020 5,935 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View