Does anyone know a reliable company able to ship biological samples in Liquid Nitrogen? ?

10 October 2014 1 3K Report

I need to send something like 80 eppendorf tubes (1,5 ml volume) in liquid nitrogen, but it's apparently quite complicated. Could someone suggest me a good company to do that?

Thank you in advance

Francesca Mariani

Thank you very much, my only worry is the uncertain time of delivery of my RNA samples, the time they could be stopped in airports, and so on, and I was told that in Liquid nitrogen they are safe for a longer time (even 10 days, is that possible?).

Thank you for your kind suggestion

Francesca

Badges
Science topic

More Francesca Mariani's questions See All

Do you have a titration protocol to use Neutral red to stain human melanoma cell lines? In medium or in HBSS?

I'm having problems in staining M14 melanoma cell line with Neutral red, because, after 1 or 2 hours of staining, and subsequent washing with PBS, they are apparently ok, but the day after they...

08 September 2014 4,665 0 View

Did anyone experience a decreasing growth rate of Staphylococcus aureus in human monocyte-derived-macrophages?

I'm using the very same stock of S.aureus but, in the time course of my infection experiments in human MDMs, the CFU absolute number in the control cells is contunuosly decreasing.

05 June 2014 1,233 4 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How to get/count refractive index in gasses?

20 February 2021 8,202 6 View

How to make Fast Green FCF from powder?

Hi everyone We need Fast Green to electroporate plasmid into mice embryos, therefore we simply need it to see some color in the liquid we are electroporating so that electroporation is more...

07 February 2021 1,671 2 View

Which is the best software for the simulation of tribological properties of materials?

I want to simulate the tribological properties of solids, liquids, and fluids, please suggest good software.

02 February 2021 3,947 3 View

Does anybody work with CoolLED in fluorescence microscopy?

I have trouble with exciting wavelengths higher than 460 nm while e.g. ex with 405 nm works. Filtercubes are correc, as I used them with my old xenon lamp before... I work on axiovert200M and with...

25 January 2021 5,201 2 View

How to prepare a liquid sample for FTIR spectrum?

I have a ethanol-water 50% extract of mango peel. I purified mangiferin from the extract with filtration and precipitation. so i obtained a low concentrated extract which i want to se the IR...

24 January 2021 8,880 7 View

Why high voltage and current (and some gases) Cause Spray-mode metal transfer in Gas-Metal Arc Welding (GMAW)?

This transition phenomena of Globular to spray mode as voltage , and especially current is raised, is very commonly known to Manual Metal Arc Welding (MMAW) and Gas-Metal Arc Welding (GMAW)...

20 January 2021 7,984 2 View

Can you have pressure inlet and velocity inlet at the same time?

I was reading a reference (Reitz-A Photographic Study of Flash Boiling Atomization). In his experiment, his boundary condition is delta p and constant velocity. The liquid injection pressure was...

18 January 2021 842 9 View

How can you confirm new liquid FTIR cell fits calibration?

We have an FTIR instrument which was calibrated in transmission/absorption mode using a set of cells for different ranges of D2O concentration. One of the cells at high range broke and the new one...

16 January 2021 4,791 2 View

Where can I find these two papers?

14 January 2021 1,572 3 View