Why am i not getting solid after reacting APTES with salicylaldehyde?

The reaction of APTES with salicylaldehyde in ethanol leads to the formation of imine compound yellow solid which is mention in literature, but I am not getting yellow solid I don't know why? when...

28 February 2021 2,955 2 View

How to calculate the crystallinity of cellulose film?

27 February 2021 2,753 4 View

How does GROMACS calculate the average structure of proteins?

I want to get a average structure from a pdb file containing multiple models. I used the command below: gmx cluster -f input.pdb -s topol.tpr -cutoff 20 -method gromos -av GROMACS...

25 February 2021 6,314 1 View

No title

The regenerated cellulose film was prepared by zinc chloride/H2O system. The zinc chloride had been washed away in the regeneration process, and the wet film which was not dried had uniform...

18 February 2021 9,538 1 View

R/Python package for time-intensity or progressive profiling in sensory evaluation?

Hi I've been looking for a stat package for my sensory evaluation data (progressive profiled which is a multi-timepoint version of descriptive analysis). Is there any available one to...

08 February 2021 9,170 3 View

How can I remove bubble in WPU film?

I am trying to prepare water-based polyurethane films. When dried air bubbles were formed and destroys the film homogeneity, then I can't use this for mechanical test because of defects. Is there...

26 January 2021 701 1 View

How can I make sure the simulation results of the water droplet impacting on the wall using the FLUENT agree with the experimental results?

Dear researchers, I am modeling the process of the water droplet impacting on the wall with a constant contact angle. The specific calculation parameters are as follows: The droplet diameter is...

24 January 2021 1,020 5 View

Mysterious line across SDS gel?

Does anyone have the similar issue? A line across the denature SDS gel shows up after staining with Coomassie blue and there are many lines in every lane if you take a closer look. This gel had 15...

07 January 2021 5,610 4 View

How can I calculate packing density of particles by fomulas or softwares?

I have all data of particles, such as size distribution, or numbers. Is there any way that I can calculate the packing density of these particles? Assume that all particles are circular.

05 January 2021 4,272 2 View

After cellulose is regenerated in water, a cellulose hydrogel is formed. I want to know if there is crystallinity inside the the hydrogel?

After cellulose is dissolved and regenerated in water, a regenerated cellulose hydrogel is formed. I want to know if there is crystallinity inside the hydrogel, or it will not crystallize until it...

04 January 2021 7,466 4 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View