How to find out or construct(?) the right priors from data of previous experiment to use in a bayesian glm?

I have the following equation, Eating choice (Yes/No)~ Box type (A/B/C). So the question is whether a certain box type affects eating choice in groups of dogs. The eating choice of each member in...

10 February 2021 6,024 9 View

What are the ways to test the knowledge level of agricultural labourer about their day to day work?

what kind of test can I do for testing the level of knowledge about their daily operation?

03 February 2021 7,583 10 View

Why the bandgap of CH3NH3PbCl3 films are different for spin-coating method and electrospinning method?

The observed bandgaps are 3.8 eV and 3.4 eV for spin-coated and electrospun films, respectively. What are the possible reasons?

08 January 2021 5,646 6 View

Why monoethanol amine is used as flocculant?

I want to know the reaction mechanism of monoethanol amine used as flocculating agent for rerefining used lubricating oil. Here I have attached one research paper where MEA (monoethanolamine) is...

01 January 2021 5,681 2 View

Problem with GST-fusion protein elution- Can anyone help?

18 December 2020 4,559 6 View

How can I determine metal concentration of Used lubricating oil by AAS?

I am a junior research fellow in the department of Chemical Engineering, Nit Durgapur. I want to know that how can I determine various metal such as Fe, Cr, Mg, Mn, Pb concentration present in...

15 December 2020 9,887 3 View

Regarding the O 1s XPS pf phyllosilciates, the peak near 531 belongs to Oxygen vacancy sites or O bonded to the Si from the silicate tetrahedra?

In O 1s spectra, usually the peak near 531 eV belongs to oxygen vacancy sites in oxides, however, in silicates, these peaks are often reported to originate from O-Si. I am confused if the intense...

10 December 2020 9,496 2 View

What is the mol. weight of GFP-11 tag?

Hi, I am trying to find out the mol. weight of GFP 11 because it is tagged to my protein of interest which is 17kDa. GFP 11 has been tagged with my protein of interest while GFP 1-10 is tagged...

09 December 2020 1,863 1 View

How to PEGylate Fluorescntl Polystyrene Particle?

I have Fluorescent Polystyrene beads. I need to graft PEG on the surface of it. I am looking for a protocol to do that. Also need to know which experiment to perform to be sure about the grating.

01 December 2020 7,860 1 View

How to control for categorical independent variables (e.g., education) when doing regression discontinuity using STATA?

I am conducting a regression discontinuity design where the dependent variable is continuous while control variables are categorical (except the treatment variable). In the usual regression...

01 December 2020 583 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View