16 May 2018 1 388 Report

relation between cutting force and tool life

More Ratan Patil's questions See All
How to estimate sample size for GWAS of continuous and discrete traits? What are the pre-requisites?

Genome-wide association study (GWAS) Continuous traits: eg. Height Discrete traits: eg. Eye color

28 July 2024 286 0 View

Is it fare for editors of reputed Journals to put on hold manuscripts more than six months without review updates, Are they harassing researchers?

It is being seen that Editors of some reputed Journals are putting on hold the manuscripts and not updating review states even passing more than six months from submission. Researchers are...

24 July 2024 8,596 2 View

Can we fit a gaussian Fit on a LIBS Peak ?

Though much literature suggests fitting a Voigt profile on a LIBS peak, is it also possible to fit a Gaussian profile on the LIBS peak? I have 204 spectra files, and I am building a pipeline for...

23 July 2024 6,127 1 View

Why is my phage library obtained at round 2 of Biopanning viscous?

After incubation of the TG1 cells with the helper phage, I spun down the culture and precipitated the supernatant with PEG/NaCl. After this, I spun it down again and resupended the pellet in PBS....

21 June 2024 6,260 2 View

Can we use LIBS Peak - Ti 441.492 for the Univarate Analysis ?

I have 17 different steel samples, in which i identified a peak of Ti 441.492. But , if you look closely at photo, while some some peak are at 441.492 , some are at the slight offset. eg 441.490...

10 June 2024 8,934 2 View

Challenges in Univariate Analysis for Stainless Steel Samples using Laser Induced Breakdown Spectroscopy?

Respected Members , I have a 17 different steel sample references , with varying concentration for Minor Elements being Mo , Ni , Mn ,Si , Cr etc , i am trying to build a calibration curve with...

10 June 2024 993 0 View

Normalization in LIBS Spectra ?

Hello Everyone ! I have a samples a satinless steel , I performed the LIBS Measurement with hLIBS (SciAps Z-300). Total of 12 measurements on different locations were done on the same sample...

09 May 2024 7,959 6 View

Is IJSREM UGC Care or cloned journal?

Some journals seems to be fake..cloned

07 May 2024 3,623 1 View

Does anyone know about Universities offering (a) PhD by prior publication or (b) PhD by portfolio?

Dear Colleagues, Does anyone know about Universities that are offering (a) Ph.D. by prior publication (b) Ph.D. by portfolio? I have two publications viz."Regression Testing in Era of Internet of...

09 April 2024 2,123 1 View

How to calculate chemical quantity required when relative molar composition is given ?

Relative molar composition of 1.0 TEOS : 0.2 CTACl : 0.0026–0.017 LS277 dye : 10.4 TEA : 142 H2O was used.

04 April 2024 6,770 1 View

Similar questions and discussions
How to increase simulation box size?

We intend to study the interaction between peptides and polymer (like PP, PE and PS) through MD simulations using Martini force fields ( Martini 2 for PP and Martini 3 for PE, PS). We have...

08 August 2024 4,842 0 View

How to apply virtual site for a polymer?

Dear All, I have a PDB structure for a complex and large polymer. I need to perform MD simulations using the OPLS-AA force field. I obtained the force field parameters from LigParGen and created...

11 July 2024 5,109 0 View

Can I use different force field for protein and ligand?

Hello, Dear! Generally, I used CHARMM36 + cgenff force field for simulaiton. But,, due to certain parts of lignad, force field cannot be generated using Cgenff. Can I use different force field...

10 July 2024 9,513 3 View

Issue with micrometer beam size while simulating moving heat source problem?

I am trying to replicate results published in the journal paper published recently (Modeling of Laser-assisted micro-milling Inconel718 ). In that paper, they used vdflux subroutine to obtain...

05 July 2024 3,701 0 View

I found trouble to run MD of my peptide with PTM in different force field. In Charm-GUI, it cant recognize the engineering residue. What can I do now?

I am working on my PTM project. I have some peptide. I got the result of doing MD of those peptide without PTM in different force field like Charm-GUI, Amber, Gromacs. Now I have to do MD of those...

05 July 2024 9,346 0 View

How validate the dynamic molecualr simulation with experimental data?

I used forcite module of Material Studio software to simulate the dissolution of zinc production waste in deep eutectic solvent. UFF force field has been used for the optimization of molecules,...

02 July 2024 7,494 1 View

I tried to do simulation using YASARA software for an optimized ligand after docking but an error is coming what should I do?

The error message is "Angle parameter for atoms42-45-15 (cf-nu-ns) not found in the force field. Initialization is not possible, check atoms for incorrect bonds, then update the force field's...

27 June 2024 3,446 3 View

What is the actual distance covered during sit-to-stand test?

Fellows, We are analysing data from force platform to calculate the power based on the acquired force. However, the current formula consider the distance covered by the individual as the "height"...

26 June 2024 2,049 1 View

Which modeling software and force field suitable for miRNA-mRNA molecular simulation?

Hello everyone, I am currently working on miRNA- mRNA interaction study. Further, I would like to do MD simulations for the miRNA-mRNA models. For the Simulation, I have modelled this complex...

24 June 2024 3,507 2 View

C3D file, how to extract a vídeo file from it?

I made a series of jump tests in subjects, everything was recorded with Vicon. I have data from markers and force plate. We recorded the tests before and after an intervention. My question is, I...

23 June 2024 9,381 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close