How much amount of DNA (ligation mix) should I use for transformation?

Hi Fellow Scientists! I am trying to clone my 300 bp insert into a 6 kb vector. I run a few different ligation reactions using (1:3 vector: insert molar ratios) 10, 20,30, and 40 ng/ul vector...

15 February 2021 9,563 6 View

Is it possible to report hydrodynamic loads on different parts of an ocean vehicle while 6DOF motion analysis in Ansys Fluent is running?

It seems a 6dof UDF containing vehicle characteristics such as mass and moments of inertia can be used for specifying a boundary as reprentative of ocean vehicle. It is required to have...

03 February 2021 7,726 3 View

How post-hoc test should I perform for two way repeated measures ANOVA for 3 groups?

Hello everyone, I have 3 groups and 4 measurements so, I performed two-way repeated measures ANOVA. How can I detect the difference (which groups and which measurements) when there is significant...

27 October 2020 4,503 3 View

Can anyone please provide information in regards to the utilization of the exoskeleton as a perturbative tool for gait/balance therapy?

There exists a considerable body of literature on the application of exoskeleton as an assistive tool in the area of gait or balance therapy. I am interested in finding out more about the...

06 October 2020 9,317 3 View

How to propagate the EMC Virus in L929 cell line?

04 October 2020 6,705 2 View

How do We Maintain Appropriate Cell microenvironment with 3D Cell Culture Method?

3D Cell Culture is newly optimized and promising discovery in cell organization research and other researches that needs evindences in cell culture (in vitro) level. Are 3D Cell Cultures mimic...

23 September 2020 7,109 4 View

How do We Clarify the Effects of Drugs on DNA Replication?

DNA Replication and its components are common targets in discovering new drugs as antimicrobial therapeutic agents especially while dealing with antibiotic-resistant species and other diseases...

21 September 2020 6,172 4 View

Is there anybody to share a RevMan tutorial file with me?

I am busy writing a meta-analysis manuscript. I had passed a RevMan course previously, however, I need to be refreshed again.

21 September 2020 3,535 5 View

Why would a negative control have apoptosis in the Annexin V-PI Flow Cytometry?

06 August 2020 3,627 22 View

What does "Mesh has uncovered edges" mean in ICEM CFD?

hello everyone, I need your help. I was meshing a porous media geometry with ICEM, and after meshing, I wanted to transfer the data to #fluent, I encountered this error "WARNING: Mesh has...

31 July 2020 3,695 3 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View