Do we really need a femtosecond laser for Laser-induced graphene(LIG) production on polymers?
Other than better resolution and lesser thermal damage is there any other advantages?
I have three drug groups with measures over 5 time points. I need to study their interaction x time. Since they are non parametric data, I am looking for a non parametric alternative for a 2-way...
21 February 2023 2,825 8 View
I am getting the following errors while doing the Hydrological modelling in HEC HMS NOTE 20364: Found no parameter problems in meteorologic model "Met1". NOTE 40049: Found no parameter problems...
30 December 2022 402 2 View
I am going to do a Dam Break analysis using HEC RAS. Is it possible to so the hydraulic modellinf with mud and debris flow along water?
15 December 2021 4,362 5 View
Average roughness of a laser ablated spot was measured using AFM and optical profilometer, I would like to estimate the improvement in surface area after laser ablation due to the roughness.
22 April 2021 3,266 9 View
I'm writing a thesis on development of business model for a wealth management based e-commerce business. In that I have one sub research question as Identifying Critical success factors for both...
13 October 2020 1,330 2 View
I have studied the effect of air preheating on non-premixed combustion, keeping the mass flow rate and inlet tube diameter constant at inlet air-fuel stoichiometry. Only the fuel flow rate is...
20 January 2020 2,403 0 View
Please help me to figurer the step to given the simulation spring back in explicit and bc also....please
06 March 2019 8,860 3 View
I was doing bending sheet metal in Abaqus. Now I have to do spring back. could any one suggest the procedure of spring back in explicit.
26 February 2019 1,669 2 View
my project is related to finding the wrinkles in sheet metal aganist the radius of bending. how can i find that. please help me...
18 February 2019 1,741 3 View
I have done a very simple combustion of a fuel mixture using the following CH4, O2, H2, H2O, CO, CO2, N2 and C2H6 as the fuel+ air with 21% o2. using ANSYS-FLUENT-Eddy Dissipation Model I have...
19 November 2018 4,748 3 View
i am unable to interpret why its increases in start as shown in figure
11 August 2024 2,175 1 View
I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.
09 August 2024 9,894 2 View
Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?
06 August 2024 978 5 View
I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...
05 August 2024 3,289 1 View
Details of the Analysis. Static Analysis Composite Layup Continuum Shell Elements FRP Material (Elastic and Hashin Damage)
03 August 2024 8,537 4 View
I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?
03 August 2024 4,622 3 View
I imagine the battery drives the graphite into a carbocation, then chloride is oxidized to donate the electron to the carbocation, but what pushes the lost electrons of chloride to be shared...
03 August 2024 5,384 0 View
I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...
01 August 2024 8,366 2 View
The starting material is a finely ground powder. Some particles contain more graphene than others.
30 July 2024 3,977 2 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View