Do we have to communicate differently suiting the context across all procurement typologies or we should use same?

More Titus Ebenezer Kwofie's questions See All

Can ArcSWAT or SWAT be used for this study?

I want to simulate soil erosion, water quality and Soil nutrients under various land use scenario. Please can ArcSWAT or QSWAT be used for this analysis? I would also welcome a suggested software...

31 March 2024 3,346 2 View

Can RUSLE and USLE be applied only in watershed or hilltop environment?

RUSLE and USLE are the prevalent soil erosion models widely used especially for catchments, watersheds, and basins. these zones are hilly or sloppy can this model be used in a nearly flat...

26 January 2024 7,377 1 View

Does corporate governance control meachanisms relate directly to financial performance or firms value?

I will appreciate detailed explanation

21 March 2023 9,064 3 View

Can somebody please suggest the best tool to view, model and edit 3D protein structures at no cost?

08 February 2023 581 12 View

What is the ASTM standard size (dimensions) of thin steel plate that can be prepared for tensile testing?

Considering a butt joint developed using SMAW

05 November 2022 7,457 1 View

What is the difference between molecular and kinetic diameter?

I'm doing research for my professor, and I'm trying to figure out which measurement I need to use. I want to come up with ideas on DAC using MOF or other possible materials that might filter...

25 October 2022 6,497 2 View

Can someone provide a resource that has a comparison between Fourier and wavelet-based power spectra?

More specifically, I want the comparison in wavenumber-based power spectra, opposed to frequency-based. That would include converting multiple signals into a cross spectrum, finding the phase, and...

16 May 2022 3,155 3 View

Please what is the best solvent to dissolve heme?

I have tried NaOH and NH3 so far but can't dissolve well.Thanks for the assistance. I can be contact personally on this email:[email protected]

04 January 2021 5,817 2 View

OriginPro Setup link?

Hello! I use OriginPro9 crack, but I noticed recently I can't add Tick Labels on the graph. I have tried resetting the Tick label display but it didn't work. Please, kindly suggest how I can...

18 April 2020 3,234 1 View

What is the best software for experimental design using Taguchi method?

Taguchi method have been used widely by researchers in the recent times due to its less number of experimental runs advantage compared to full factorial design and response surface method. For...

31 March 2020 2,536 14 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Irene B. Teich

Different procurement typologies should be answered in different way. Communication has to fit the situation. Automation reduces the effort to do so. The effect is better results - higher reliablity, good punctuality and a good partnership with suppliers. That are my observations from practice during consultancy projects.

Titus Ebenezer Kwofie

Thanks Irene for your insightful comments