How to submit an analysis using solid and truss elements in Abaqus?

13 November 2020 4,962 3 View

Data recovery after abnormal termination of Matlab ?

07 July 2020 1,256 3 View

How to calculate the seismic force for a Pushover analysis and how to insert it in Abaqus ?

Hi everyone, Iam performing a pushover analysis on historic masonry structure and i would like to be sure that the lateral seismic force calculation is correct. 1- I calculated the lateral...

13 April 2020 2,071 3 View

Does TV sports media keep pace with social media websites?

How can TV sports media transmit and keep abreast of all national and international sporting developments in light of what the various social networking sites offer on the Internet, especially as...

22 January 2020 3,696 3 View

About spin canting effect?

How to know if the complex (specially azido compounds) presents a spin canting effect? From the Chi T vs T graph?

20 September 2017 8,536 2 View

How can I tune fuzzy membership function with genetic algorithm in matlab(mfile)?

Number of memebership exceeds 3 of each variable

20 January 2015 754 3 View

What is the significance of IC50 value when the drug is exogenously administered to an animal tissue?

.

13 December 2013 2,451 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How to extract the y+ value from fluent ?

I am doing a 3D steady simulation of a wind rotor using Ansys Fluent. In order to have a y+ of 1, I created 10 inflation layers using total layer thickness method, and I started a first...

23 February 2021 2,819 3 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

How do I add a udf to Ansys fluent and does it need to be compiled before hand ?

I have a Define_CG_Motion udf written in c where do I add it to my Ansys fluent project and does it need to be compiled before that?

21 February 2021 9,347 3 View

How do I plot Pressure against crank angle degree in Fluent?

18 February 2021 8,390 3 View