last month 1 402 Report

Ultra High Strength Steels

More Arnab Ghosh's questions See All
Z-average size from Dynamic Light scattering can it be lower than the original probe size?

Hi everyone, Recently I have been conducting Dynamic Light scattering experiments in a micellar solution at 5 and gel at 37 degrees of Celsius with latex particles of diameter 190-500 nm. While...

01 August 2024 1,168 4 View

GSH estimation assay: What is the right choice of standard?

Hi there, My question is: What standard curves should be used while estimating Tot GSH and GSSG by kinetic method using GR enzyme mediated recyling with DTNB chromophore? Actually I am following...

01 August 2024 8,217 1 View

Intracerebroventricular (ICV) AAV inj.?

I'd like to know if anyone has got experience in intracerebroventricular (ICV) AAV inj. I am looking for a concomitant spread of the AAV including but not limited to the motor cortex and the...

12 July 2024 781 0 View

What is the maximum acceptable degradation of gain in the orthogonal plane relative to the beam scanning plane for beam steering antennas?

In research papers on beam steering antennas, while the radiation pattern for the beam scanning plane (such as the horizontal or vertical plane) is typically presented, details regarding the...

03 July 2024 8,321 0 View

What is the term REF referred for renewable energy based power system optimization?

RENEWABLE ENERGY , REF, POWER SYSTEM OPTIMIZATION

25 June 2024 6,630 5 View

What kind of surface morphology must be there for good photocatalytic activity of thin film?

If I want to increase the photocatalytic activity of a thin film sample what should be it's ideal surface morphology and parameters? All scientific answers related this are highly appreciated.

19 June 2024 6,744 0 View

Why I am getting follwing error when I tried to open .dta file in SPSS25?

>Error # 7202.  Command name: GET STATA >Input dictionary read error. >Execution of this command stops. Cross Product Matrices are not supported

19 June 2024 5,423 0 View

Which deposition technique is better (Spin Coating/Dip Coating) for making Ni doped ZnO thin film for better photocatalytic activity?

If I want to improve the photocatalytic activity of Ni doped ZnO thin film then which would be the better deposition process for thin film Spin Coating or Dip Coating?

18 June 2024 7,678 2 View

What are the possible parameters needed to be tuned for better photocatalytic activity of thin film?

If I want to enhance the photocatalytic activity of Ni doped ZnO thin film. For this what are the parameters I need to tune and how? Related this all scientific answers/explanations are highly...

16 June 2024 4,533 1 View

Curing of Novolak resin with hexamine develops yellow color. I believe it is due to azo linkage -C-N=N- C- What is the reaction mechanism?

Also, I will appreciate whole curing mechanism of Novolak with Hexamine

14 June 2024 9,908 0 View

Similar questions and discussions
Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

London dispersion in CCl4 vs the dipole-dipoles force strength in CHCl3?

How do you tie-break and rank these two in their strength?

03 August 2024 4,471 1 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

A twin-shaft kiln or a rotary kiln for lime production 1 class? if compressive strength of limestone is low 60 MPa?

My research work is related to the calcination of limestone. I have a complex question and would like to consult with experts in this field. Could you please advise which kiln to choose (a...

18 July 2024 1,390 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close