Density and viscosity of sodium hydroxide solutions

More Łukasz Wieczorek's questions See All

Material, energy and momentum balance literature

Can anyone suggest some position in literature with wider insight on material, energy and momentum balance, both in general and particular cases?

04 May 2013 5,419 4 View

What size could a single cyclonic wet scrubber reach?

I'm asking especially according to height dimension.

04 May 2013 8,249 1 View

Thermophysical data for water sodium sulfite (IV) solution

I'm looking for the following properties of sodium sulfite (IV) solution: - Heat capacity in water solution - Thermal conductivity in water solution - Diffusivity coefficient in water solution

02 March 2013 2,283 2 View

How to predict overall diffusivity of each component of the liquid solution of NaOH, Na2SO3 and NO2?

I'm working on absorption of SO2 and NO2 with chemical reaction in NaOH solution. To make it easier, the reaction with NO2 does not exist, and only the reaction SO2+NaOH-> proceed irreversibly and...

01 February 2013 7,733 1 View

How to get diffusivity of water in electrolytes.

The diffusivity of electrolytes in water could be easily obtained, however, when the multicomponent matrix is to be created, both binary diffusion coeficients are needed. Does anyone know an...

01 February 2013 2,486 1 View

Aqueous sodium sulfate viscosity

Does anyone know any data for aqueous sodium sulfate viscosity in range of 0 to 100°C?

01 February 2013 4,763 4 View

In which cases is the diffusivity of an electrolyte in solvent the mutual diffusivity?

Both solvent in solute and solute in solvent?

01 February 2013 476 5 View

Does anyone know of correlations between Falkenhagen relations parameters and temperature? Or do you know of alternative ways of predicting visco in electrolyte sol.?

Falkenhagen relations are for the prediction of viscosity of electrolytes. This book presents the method...

31 December 2012 4,013 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Research Methodology - Impact of Corporate Reputation on Stakeholders Behaviors?

Please can anyone support with the survey questions based on RQ measures and propose how to do it in FMCG industry and include as well the role of brand equity Thanks

06 August 2024 949 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Anyone having idea about VN primer for miRNA primer design ?

How to design VN primer to attach with universal reverse primer

05 August 2024 2,116 3 View

Wu Yi Hsuan

http://www.vinnolit.de/vproducts.nsf/allPages/50AB7B8678A88129C12573B1004E7AC1/$file/Produktdatenblatt%20NaOH50-en_02.02.2011.pdf?open

I'm not sure if this is suit for your requirement.

Scott Campbell

http://www.solvaychemicals.com/Chemicals%20Literature%20Documents/Caustic_soda/PCH-1110-0006-W-EN_WW_.pdf

Hemamalini Rawindran

you may refer here

Rahmani Youcef

Hemamalini Rawindran hello, please you have the reference of these results?

hello sir, this table had been done manually by our fellow researches :)

Hemamalini Rawindran hello, thank you very much

You're welcome