Dear colleagues, do you have the CNN algorithm code in Matlab software?

More Hayder Dibs's questions See All

How to solve melting and solidification of PCM using ANSYS Fluent?

Dear colleagues; I modeled 3D melting and solidification of phase change material filled heat exchanger and generated a (as in the picture below). First, I enabled melting and solidification...

19 January 2021 1,126 4 View

What are the shape functions of rectangular Q4 and triangular CST element models in natural coordinate system with (s,t) that ANSYS APDL will be used?

What are the shape functions of CST triangular and Q4 rectangular element models in terms of natural coordinate system (N.C.S) with (s,t) not with (x,y) in software programs as ANSYS mechanical APDL?

13 January 2021 7,968 4 View

What's the best suitable area element type like 182,and 183 quadrilateral and triangle for analysis of 2D FE modeling results, beams in ANSYS APDL?

I want to analysis of 2D FE modelling beams cantilever/simple support in ANSYS, then compare it with exact solutions (elementary) such as deflection or stresses, however what element types (solid...

07 January 2021 8,744 1 View

What's the best appropriate area element type like 182,and 183 quadrilateral and triangle for FE modeling results,analysis of 2D beams in ANSYS APDL?

I'm trying to carry out analysis of 2D FE modelling beams cantilever/simple support, then comparing it with exact solutions (elementary) such as deflection or stresses, but what element types...

06 January 2021 1,038 3 View

Why does bending stress(Sx) in ANSYS APDL direct below of point load FE 2D modelling simply supported point load higher than exact solution in value?

Why does normal bending stress/flexural stress value (Sx) just direct below a concentrated load of simply supported beam which is compression stress higher than the hand calculation Exact solution...

03 January 2021 8,462 3 View

Why does shear stress (Sxy) result in ANSYS APDL area element type solid 182 or 183 quadrilateral or triangle will be efferent in a cantilever beam?

Why does shear stress (Sxy) result in ANSYS APDL area element type solid 182 or 183 quadrilateral or triangle will be different in a cantilever beam with point load at fixed end or uniform load at...

31 December 2020 9,359 3 View

How to show effects of baffles on fluid flow?

Hello All I'm working on baffles inside a circular pipe, the problem that I'm facing is when I draw contour or streamlines, I have not found any effects for the baffles on fluid flow where fluid...

23 October 2020 2,002 3 View

How to select best Probability Distribution Function (PDF) for time series of extreme value data sets based on multiple Goodness of Fit (GOF) tests?

I have prepared an analysis of time series extreme values data sets (9 sets for different storm durations) by using three PDFs i.e. General Extreme Value (GEV), LogPearson III (LP III), and Gumbel...

11 October 2020 3,331 2 View

Can oligo hexamer primer produce sequencing error?

Hello everyone I conducted sequencing prosedure for RNA genome segment (about 700nt) , for this reason I employed the random hexamer primer for cDNA synthesis . after sequencing (by sanger...

16 August 2020 3,994 3 View

How do I know which type of mesh and its method is suitable for my geometry in ANSYS? How do I choose the right mesh?

If I wanna work on geometry and wanted to create a mesh for it, how can I be sure that my mesh I choose it is the best to give the right results

21 January 2020 6,095 4 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

How could I process data in RCT to include it in meta-analysis?

I'm in the process of doing a meta-analysis and have encountered some problems with the RCT data. One of my outcom is muscle strength. In one study, I have three different measurements of muscle...

25 February 2021 7,603 3 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

Satellite orbit estimation using Recurrent Neural Network - what should I use?

Hello, I am a master's student studying in Yonsei Univeristy, Korea. I am trying to estimate the state of satellite, using Neural Network. Below is a simple flow of my study. 1. Train (t0 ~ t1)...

23 February 2021 6,383 3 View

Any Differences in COVID-19 vaccines?

Are there any differences (outside of the clinical trials that led to their EUA) observed in the rate of infection among those who have received the Pfizer vs Moderna vaccine since the mass...

22 February 2021 9,727 6 View

How can I get the coding gene sequences of Hela and U2OS cell lines? Is mRNA sequence of Hsp90 alpha tissue specific??

I am looking for hsp90 mRNA sequence in Hela and U2OS cell lines, I have tried through ncbi but always the output is hsp90 in homo sapiens not in the specific cell line. Kindly, could any one...

22 February 2021 1,853 3 View

How to constrain genetic algorithm input u?

My real system (buck converter) can only take an input of 0 to 1 (duty ratio) and I need to constrain the system so the controller action keeps within this bounds. How can I do this? The code for...

22 February 2021 2,125 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View