I want to identify cycling voltages for my non-aqueous redox flow cell. Does Cyclic voltametery can help me to get the charging-discharging voltages of my redox cell.
Following links may help you
http://pubs.acs.org/doi/abs/10.1021/acsenergylett.6b00255?journalCode=aelccp
http://pubs.rsc.org/en/content/articlehtml/2016/ta/c6ta01177b
http://ma.ecsdl.org/content/MA2015-01/2/420.abstract
http://jes.ecsdl.org/content/163/7/A1442.full
https://www.ncbi.nlm.nih.gov/pmc/articles/PMC4681342/
https://www.ncbi.nlm.nih.gov/pubmed/25891480
Regards,
Dear Kashif,
Yes, Cyclic voltammetery will help you to get the charging-discharging voltages for the redox cell.
Best regards,
Bapi
Bapi . . Thanks for your reply. Can you please further explain how it could help to identify this cycling range?
I know that Zinc Iodide and Zinc Bromide has good solutbility in water but I am working on Non-Aqeous systems. So, kindly share if anyone used these chemicals with acetonitrile.
01 February 2018 548 4 View
I have the data of my CV and I can plot it. But I want to know if any software can help me in analysis of peaks.
09 October 2017 4,511 0 View
Which material of the tubing is suitable for organic solvents (like Acetonitrile, DMSO, 1,3 Dioxalene) while working with peristaltic pumps?
01 January 1970 9,461 4 View
I am working on redox flow battery using non-aqueous solvents and currently in the membrane selection phase.
01 January 1970 3,613 3 View
Which is the accurate experiment to check solubility of active species in an organic solvent (Acetonitrile)?
01 January 1970 8,697 0 View
I need an experimental device to check solubility of active species in solvent. It is done to synthesise electrolyte.
01 January 1970 8,954 4 View
My electrodes should facilitate a good wettability (degree of wetting which is the ability of a liquid to maintain contact with a solid surface). But, how to measure it experimentally?
01 January 1970 7,987 3 View
Most of the literature is related to use of Metal Acetylacetonate as redox species for NARFB. Is there any particular reason other than solubility?
01 January 1970 506 2 View
My objective is to scale down the size of existing redox flow-cell. I can get experimental data of spectro-photometery & conductivity meter for flow pattern of redox flow cell. Using this...
01 January 1970 4,152 0 View
Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...
03 March 2021 5,999 3 View
Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...
02 March 2021 1,999 5 View
I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...
02 March 2021 9,945 3 View
im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...
02 March 2021 2,246 2 View
Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...
01 March 2021 3,867 3 View
I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...
28 February 2021 4,851 8 View
28 February 2021 2,534 2 View
I diluted siRNA and RNAiMAX in opti-MEM and added to the cells which they were in the growth medium. Is it a right way? or should I culture cells in the opti-MEM medium for a while and not in...
26 February 2021 10,041 3 View
I am looking to package lentivirus in endothelial cells but I am opposed to using 293 cells due to personal ethics regarding the source. I have done some reading and saw that COS1, COS7, & CHO...
25 February 2021 3,030 1 View
Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...
25 February 2021 9,602 4 View