Could you tell me in the estimation of the small-strain shear modulus based on the shear wave velocity what kind of density should be employed?

Navid Yeganeh @Navid_Yeganeh

02 February 2017 0 10K Report

(saturated soil):

saturated (total) density

saturated density - water density

Badges
Science topic

Similar topics
Agriculture
Soil Science
Soil

More Navid Yeganeh's questions See All

Should the effective stresses be constant during the effective stress numerical analysis?

Assuming running the undrained effective stress analysis in FLAC3D via Config FLUID using the effective stiffness and strength parameters, are we expecting the constant effective stresses in the...

06 July 2019 8,943 3 View

How can one remove the water level from the FLAC3D simulation at some point?

Is it possible to deactivate the effect of water so that FLAC adds the amount of steady state PWP to the effective stresses in all zones such that all the stresses in the soil constitutive model...

05 June 2019 5,263 2 View

How are the horizontal stresses calculated in FLAC3D?

The very initial step of each project is setting up the in-situ stresses. Right after the said step as well as amidst the dynamic analysis, could you cast light on how FLAC internally does the...

04 May 2019 2,205 1 View

How to assign the appropriate values to the interface element properties in FLAC3D?

Hey There. I am seeking a batch of references whereby the cohesion, friction angle, and dilatancy of the interface element, e.g., between a concrete foundation and the soil mass, could be...

02 March 2019 808 3 View

In what condition is the assumption of the constant effective major stress applicable?

I was wondering what were the rationales behind making such an assumption in the soil mechanics and geotechnical earthquake engineering? Is it allowed to be used only in the static condition or it...

01 February 2019 4,073 1 View

Could you please set forth why the most of the increases in the pore-water pressure in the undrained condition would occur during the unloading?

Please find enclosed the attachment.

11 December 2018 9,455 1 View

How to elaborate the diminishment of PWP in the vicinity of a foundation in a soil-structure interaction system amidst an earthquake?

PWP: Pore-Water Pressure

09 October 2018 2,393 0 View

Where can the journal abbreviations be found?

I am wholly grateful to you if the Civil Engineering journal abbreviations source could be announced herein. TA! Navid

05 June 2018 1,185 2 View

Would you please shed light on the rationale behind the statement below?

The yielding stress of concrete material is considered to be the same as the characteristic compressive strength (fc0) of concrete.

05 June 2018 8,489 0 View

What is the appropriate distance between the side boundaries in a 3D numerical model of a soil-structure interaction system for a seismic analysis?

For instance, Rayhani and El Naggar (2008) posited that the said distance ought to be greater than five times of the superstructure width. Rayhani, M. H., & El Naggar, M. H. (2008). Numerical...

05 June 2018 536 4 View

Problem with shRNA transfection. Why are only two plates getting contaminated instead of all?

I transfected my LNCaP-WT cells with 3 shRNA plus their NTC two weeks ago and split two puromycin selected cell plates on Friday last week(Feb 26). I checked for GFP in the cells, and they all...

28 February 2021 4,949 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Is this the write procedure for acid digestion of soil for heavy metal analysis using AAS?

How to do acid digestion of soil sample with 3:1 aquaregia in an open vessel?

23 February 2021 3,053 7 View

Is there a suitable way to confine cell attachment area inside a multi-well plate?

Are there any types of cylindrical cell culture inserts that are designed to confine cell seeding area? Say, if I'm using a 12 well plate (3.5 cm^2/well), but only want to seed cells in the middle...

22 February 2021 7,127 4 View

Are there packages (R or Python) for simple models (bucket?) to assess soil water content?

Hi everyone. I am researching droguht effects on soil water drought. I am looking for already implemented functions in R or Python to estimate soil water content from precipitation,...

21 February 2021 2,084 1 View

Which type of loading is to be used in dynamic analysis of Machien foundation?

Hello Everyone, Hope you all are doing well. I'm trying to simulate a machine foundation in ABAQUS with a geo-cell reinforced soil bed. Im totally confused to which type of loading would be...

21 February 2021 4,388 3 View

Hi..how to isolate crude HDL (all subfractions) from human serum by size exclusion chromatography?

I would like to know about isolation of crude HDL from serum by SEC. Is it possible to perform with a serum sample volume of

19 February 2021 5,576 2 View

How to calculate the Atomic Polar Tensor using DFT ?

Dear friends, I am a beginner at DFT calculation. I have done a structure optimization using DFT- B3LYP/6-31G*, Nevertheless, I don't know How to calculate the Atomic Polar Tensor (APT) in...

17 February 2021 9,082 3 View