Could you please recommend reputable researchers or research journals that delve into scram jet engines with air throttling?

Sanjibonny Buragohain @Sanjibonny-Buragohain

20 January 2024 0 6K Report

The focus should be on examining kerosene fluid as the inlet fluid and placing significance on determining the specific value of carbon dioxide in this context.

Badges
Science topic

More Sanjibonny Buragohain's questions See All

I need this book for designing adiabatic fixed bed reactor for methanation. Can anyone recommend any source to get this book from?

Heterogeneous Reactions: Analysis, Examples and Reactor Design: Gas-Solid and Solid-Solid Reactions L.K Doraiswamy and M.M Sharma

21 September 2020 6,595 3 View

To compare the efficacy of a new drug versus standard drug, is it necessary to have same route of administration in open label study?

The drugs I have chosen to compare the efficacy have different routes of administration, one orally and other intravenously. It is an open-label nonrandomized study.

09 March 2020 5,023 3 View

How do we use two different basis sets for two different type of atoms in geomtry optimization calculation in gamess?

Dear all, I have been trying to optimize a molecule that contains Fe and H atoms using B3LYP hybrid functional. For Fe, I am considering 6-311G basis set, while for H atoms, 4-31G basis set is...

09 April 2018 6,074 6 View

Why does the ITC curve in an interaction between a DNA aptamer and peptide ligand have both exothermic and endothermic peaks at the same time?

I am using MicroCal ITC 200 (GE) and performing an interaction study between a DNA aptamer (12 kDa) and a peptide ligand (1.91 kDa). How can I explain an ITC curve with both negative and positive...

27 December 2017 233 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View