Could anyone provide some practical LS-DYNA models for learning?
Yao Lu,
you can use practical workshops like this https://en.banumusagr.com/shop/low-velocity-impact-frp-laminate/
or get mentoring for your projects https://en.banumusagr.com/cfd-fea-consultancy/
Good luck
Hello everyone! I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...
05 August 2024 5,729 2 View
Dear all, I gave 116 respondents 18 translated sentences and asked them to indicate their levels of acceptance of these translations on a five-point scale. Some translations result from strategies...
24 July 2024 8,245 5 View
"The Correlation between Nutrition and Transport Mechanism under Abiotic Stress in Plants: A Comprehensive Review" by Muhammad Saleem, Jianhua Zhang, Muhammad Qasim, Rashid Iqbal, and Li Song,...
23 July 2024 9,109 0 View
In other words, I did not use the trained XGBoost model to make predictions on the test set and then use SHAP for interpretation. The reasons are as follows: Even with the best and most...
26 June 2024 7,332 1 View
I carried out low-cycle fatigue tests on a secondary-hardenning ultra-high-strength steel with test condition εmax = 0.9%. It was found that the fatigue life at high temperature was much higher...
29 May 2024 3,176 1 View
Hi, Just a quick question for those who have profiled cytokines using sera or cell culturing media supernatant samples. I compared the sensitivity of these two in their manuals and found BD CBA...
14 May 2024 4,596 0 View
Perform Experiment and report
11 May 2024 3,449 1 View
I want to calculate the drug combination index in my macbook, but I cann't find the compusyn software.
03 May 2024 1,115 1 View
Hi there, I am doing regular confocal experiments to observe my over-expression target protein localization. (which is novel, encoded by a novel transcript, that is all I can say). My OE protein...
01 May 2024 4,809 2 View
The question is based on the article “Tenets of Specimen Management in Diagnostic Microbiology” by Rajeshwar and Pathak. It explores how advances in technology, specifically barcoding systems, can...
10 April 2024 9,863 1 View
Hi, I am working on a head FE model and want to try different material types on brain. I read some papers that use Mooney-Rivlin rubber model and wondering if i can add viscosity into it. Is it...
24 July 2024 5,908 0 View
LS-DYNA finite element simulation:During the battery impact simulation, some units experienced failure and subsequently underwent penetration. How can this issue be resolved?
24 June 2024 3,917 0 View
I want to extract basement shear force in LS-DYNA calculation result, but i found that there were no force results but only moment results in SPCFORC even I check the model and make sure the...
23 June 2024 2,691 0 View
Hi, I run an FE model on LS-DYNA solver, and concerning about the max principal strain contour result in HyperView. When I choose the result type as Strain(t)-Absolute Max Principal the contour...
19 June 2024 7,577 1 View
Please anybody suggest me which ls-dyna material card is suitable for windshield sealant material to prepare material card and to validate for crash performance Thank you in advance.
16 May 2024 2,569 0 View
I am trying to model a variable thickness composite part in LS-DYNA and I am unsure on how to implement this. I have used PART_COMPOSITE in the past when testing with a composite part with the...
23 April 2024 9,376 1 View
more details about ls_dyna material *Mat_252
22 April 2024 5,398 0 View
I am facing a problem with the simulation of the precast concrete beam with prestressing. Typically, a precast beam would be fabricated in the factory with prestressing tendons (precambering) to...
06 February 2024 1,046 1 View
Hi all, I'm working on a 2D model where I impose a force to the lower part, and then I want to impose a horizontal tiny displacement on the same part. So I chosen to decompose this model into 3...
04 February 2024 881 0 View
Hi, I am trying to create a script for a particle that impact on a substrate. I want to run multiple simulations with varying particle sizes, that would run automatically. How would I go about...
17 January 2024 3,581 1 View