Perform Experiment and report
For high torsion demand, stainless steel is a suitable choice due to its excellent strength, ductility, and resistance to corrosion.
Kindly response
08 August 2024 1,214 2 View
I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...
03 August 2024 6,070 3 View
I am new to research. The boiling point of triethyl amine (NEt3) is 89 degrees centigrade. I am skeptical that when I will let the hydrogen escape which is getting generated in situ, I will also...
21 July 2024 7,284 4 View
I want to know that n-doped side of solar cell is connected with positive or negative electrode.
20 July 2024 1,348 2 View
Dear Colleagues, I hope this message finds you well. My name is Noor Al-Huda K. Hussein,and I am a researcher specializing in deep learning applications in genetic data analysis. I am currently...
18 July 2024 5,562 0 View
Dear Colleagues, I hope this message finds you well. My name is Noor Al-Huda K. Hussein, and I am a researcher specializing in deep learning applications in genetic data analysis. I am currently...
16 July 2024 3,981 6 View
i want to delete my research paper.
09 July 2024 6,554 2 View
I'm working on the proteome (from Uniprot), as you're probably aware that there are reviewed and unreviewed proteins, however unreviewed proteins are in large quantities, but reviewed proteins are...
09 July 2024 5,782 2 View
Hello, I want to load Remedesivir (RNA polymerase inhibitor) into mesoporous nanoparticles (MSNs). The issue is drug is temperature and pH sensitive and it degrades quickly. I need advice on its...
01 July 2024 889 3 View
Hello I have prepared metal nanoparticles and did zeta potential. Normally there is a single peak in sample but now there are 3 peaks. I prepared sample for analysis first I prepared 10 mg/mL...
30 June 2024 1,063 4 View
I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...
07 August 2024 1,686 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...
07 August 2024 3,218 4 View
Hello everyone, I have recently started using the microtome device for sectioning of paraffin-embedded mice lung. While I had some success in sectioning and observing proper ribbons, some of my...
06 August 2024 666 4 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
Excavation in 2007 in Northern Scotland along the East Coast revealed a domestic site containing the unbroken half (other half is missing) of a perforated circular disc measuring L 37mm x W...
27 July 2024 6,019 0 View
Are both ways acceptable, or is there any convention to them? Thanks.
22 July 2024 6,988 4 View
Currently I need to calculate detection probabilities (PD) from radar cross section (RCS) data. Beta distribution parameters for this RCS data are calculated and will be used in Swerling0...
22 July 2024 868 0 View
Hi everybody, We are trying to write a systematic review meta-analysis paper. But I could find 19 references. I think 19 references are not enough to do a meta-analysis section and it is better to...
10 July 2024 5,490 5 View
Occasionally we observe lack of staining in the inner part of a skin section processed with indirect immunofluorescence. Can be due to incomplete removal of the cryoprotectan during the wash? Any...
07 July 2024 8,200 2 View