Could anybody help me in my Research work ?

Gopikrishna Nidigonda @Gopikrishna_Nidigonda

10 October 2017 0 3K Report

"STUDIES ON CASTINGS OF HIGH MANGANESE ALLOY STEEL SHOVEL TOOTH WITH HIGH WEAR RESISTANCE" Please guide me the procedure for doing my research

Badges
Science topic

More Gopikrishna Nidigonda's questions See All

In Scopus indexed journals, how to find out whether a journal is peer reviewed or not ?

can you please advise how to find out whether a particular journal is peer reviewed or not through scopus.

10 November 2018 5,059 11 View

What type of polyhedron ?

uploaded image

31 December 2017 7,799 1 View

Do we have a Technology of light without rays and reflections ?

Do we have a Technology of light without reflections ? To have a nice and happy journey in nights on highways... IF NO, Expecting a Technology, Because of full lightings with heavy reflecions, in...

07 August 2017 1,641 1 View

How to enhance the teaching abilities ?

Teaching abilities using teaching strategies

02 March 2017 5,437 5 View

How good allowing students using mobile for flipped learning in a classroom?

"Teaching students through flipped learning" in a classroom. How good allowing students using mobile for flipped learning in a classroom?

02 March 2017 3,411 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Polymer wear calculation?

What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?

04 August 2024 1,078 1 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,115 0 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

Correct statistical approach for a hermit crab shell exchange experiment?

Hello, I'm planning a shell exchanging experiment with two marine, hermit crab species inside of a tank. I only have one tank available for this experiment. I plan on running 30-40 shell...

20 July 2024 5,676 3 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View