Correlation coefficient in calibration in groundwater modelling?

25 April 2020 0 6K Report

The correlation coefficient between the observed head and calculated head is approximately 5.5.. What should be the value for reasonable level of good calibration... say attempting that the correlation coefficient is 0.8 or 0.75

Badges
Science topic

More Paras Pujari's questions See All

How do you maintain predator prey relationship while managing the protected areas ranging from mountain watershed to flood plains of (low land) ?

In context of landlocked country( like as Nepal)

11 May 2024 1,514 0 View

Why my Twin-Strep tagged protein is not eluting out from Strep-Tactin® Superflow® high capacity resin?

Hi, I am using Strep-Tactin® Superflow® high capacity resin by IBA to purify a Twin-Strep tagged fusion protein at N-terminal. I am facing issue to elute out the protein. For elution I have...

30 December 2023 5,239 1 View

Hello, are all the niches where disseminated tumor cells stay dormant are antimetastatic in nature? How will you consider cells in perivascular nichs?

I am little bit confused to understand whether all the niches where cancer cells remain dormant are antimetastatic niches? How will we consider the accumulation in the bones?

15 November 2023 4,239 4 View

Dependence of the Carbon Black content on electrical tracking resistance on polyethylenes ?

Hello dear researchers : Does anyone have a scientific report where the curve for the dependence of the Carbon Black content on the Electrical Tracking Resistance for, either a natural...

06 September 2023 2,183 2 View

In Bldc motor on what basis the stator slots number are decides?

I am doing motor designing.

24 July 2023 7,625 0 View

Comsol Simulation of a Plastic Plate between a High Voltage potential and Earth ?

Dear friends : Is someone there who knows Comsol well, and had made before: Comsol Electromagnetics simulations, coupling the Joule Heating in Solids with Electromagnetics ? If someone can help...

26 June 2023 4,641 0 View

Why I cannot get the correct Temperature profile graph on COMSOL ?

Dear Researchers : I will very much appreciate the help. I have a 2D model in COMSOL. It's a plate, made of Polyethylene. An AC Voltage is applied on the upper electrode, the lower electrode is...

25 June 2023 3,240 2 View

Help with a Comsol simulation about partial discharges (electrical tracking) across a plate ?

Dear Researchers : Can anyone help me with this simulation in COMSOL? I'm trying to solve for the Electric Potential and Electric Field trough this plate The potential difference is 2.5 kV And...

21 June 2023 6,015 0 View

How to compute the Capacitance (between Phase and Ground) of a Power Distribution Overhead line ?

Dear Professor, Scientists and Technicians in the field : I'm trying to compute the Charging Current for a particular distribution Overhead line (25 or 35 kV). And I found a paper where I found a...

02 February 2023 6,463 5 View

Charging Current in Distribution Overhead Lines ?

Dear Professor, Scientists and Technicians in the field : I'm looking up on how to determine the Charging Current in a distribution (15, 25 or 35 kV) overhead power line. These lines are...

02 February 2023 7,329 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View