Consider a steel intended for machinery fabrication in which the maximum amount of martensite is desired after quenching?

02 February 2015 0 8K Report

Being the metallurgical engineer of the company, can you recommend how it may be process?

This was a question from our professor in Physical Met. in our class. Please help. Thanks

Badges
Science topic

More Adel Iligan's questions See All

How can you determine the rate controlling step base on mass tranfer coeefficent of elements in metal and slag?

I've already calculated the mass transfer coefficient of Cr,Ni,Si,Fe, and Mn in both slag and metal. How can you determined if it is metal phase controlled or slag phase controlled.?

04 May 2017 1,680 3 View

What is the effects of time and temperature on the rate of removal of sulfur from a copper sulphide ore?

This is by oxidation hearth roasting.

09 October 2016 3,542 1 View

What is the best book for Electrometallurgy?

Please help. I need it in my major class.

07 August 2015 8,503 1 View

Can you suggest a book for Physical Metallurgy?

I'm an undergrad student, I already have Principles of Physical Metallurgy book by Reed-Hill but it gives me headache in studying. Can you suggest other book? Please help.

11 December 2014 5,202 2 View

What is the difference between Thermal supercooling and Constitutional supercooling in the solidification of pure metals and alloys?

This is in the topic of Solidification of Metals. I just want a solid explanation on this one. Please help.

11 December 2014 4,463 10 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Best mask design for metal deposition aiming build a Perovskite solar cell device?

What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?

31 July 2024 4,835 3 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View