We're working on boosting the conductivity of 3D-printed PLA/ABS samples. Among these two samples, which one will be an easier option to apply the conductive coating?
if we are doing non-invasive sensing in patient urine then require ethical permission or not??? If we have a consent form fill with the patient then it is sufficient or not???
24 May 2024 956 0 View
Hello all, I am currently in the process of conducting a chromosomal aberration test using whole blood samples to test toxicity of nanoplastics, and I have a question regarding the protocol. In...
17 March 2024 2,919 1 View
My CV profile shows redox peaks at around -0.3V in the potential window -0.7 to 0.3V. But in GCD, the discharge curve is not going below -0.25V. If the potential window of GCD is followed i.e....
29 January 2024 9,836 3 View
Can we partly cure Butyl rubber sealant formulation at room temperature in 10-15 days time. The purpose of adding a curing system in the formulation is to add the tensile in the product without...
24 January 2024 3,285 3 View
Hi Can anybody help us to know how we can make zinc disorbate ?
23 January 2024 3,884 1 View
Since its multidose injection, we have benzalkonium chloride as preservative in formulation. we knew that benzalkonium chloride also act as cationic surfactant. During stability, How to avoid the...
01 January 2024 2,610 3 View
In my study I have observed that the capacitance retention rate after 1000 charging-discharging cycles increased beyond 100%. can anyone kindly provide insight in this regard. Thank...
21 December 2023 2,848 1 View
The amount of reagents to be taken
02 December 2023 3,481 0 View
procedure of preparation
19 November 2023 4,484 1 View
brain tumor detection and classification
22 September 2023 5,109 1 View
Could you recommend some articles on Urban Transportation System optimization and Innovation?
13 August 2024 2,595 3 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 940 3 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,297 0 View
I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...
07 August 2024 5,176 3 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,524 4 View
Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...
03 August 2024 7,842 1 View
Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...
31 July 2024 5,784 4 View
Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...
30 July 2024 905 2 View
I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...
30 July 2024 3,292 3 View
Hello everyone, I am new to this characterization but watching videos on youtube I have already plotted a Nyquist plot (Z' and -Z'') and already fitted models on my material using Zsim. But now I...
29 July 2024 1,376 0 View