i did some simulation to prove of accuracy of transformator, is model 2 valid? because the result between them was different
in zip, i attached of my model in ansys maxwell, hope anyone here can check it if i do mistake
thanks before.
Hello, I was not able to open your attachments but if I have understood your question, I think this article
https://www.researchgate.net/publication/291356147_Materials_and_Constructions_for_Magnetic_Cores_for_Impulsed_Transformers
may be useful to you.
Conference Paper Materials and Constructions for Magnetic Cores for Impulsed ...
And another thing that perhaps will be useful
https://www.researchgate.net/publication/291354725_Design_of_Pulsed_Transformers
Conference Paper Design of Pulsed Transformers
thank for your help sir
Dear All, mirna primer showing some problem in the melting curve? any idea why? As attached is the melting curve. The forward sequence is obtained from miRBase and reverse primer is universal.
28 February 2021 5,008 4 View
Can any Plant Biologists give an explanation as well as introduce me the related literature explaning why these trees flowering only on one side of tree? The effector is light, temperature or what...
25 August 2020 4,107 3 View
I'm working on a meta-analysis regarding the effect of interventions on the incidence of aggression against health workers. One study in particular compares the percentage of staff of that reports...
03 March 2020 7,583 2 View
Did anyone transform un-digested pPICZalpha-A (circular DNA) which was inserted a desired gene into Pichia pastoris using electroporation? According to User Manual's Invitrogen (EasySelect Pichia...
01 March 2020 6,604 3 View
Do anyone know is it necessary to use low attachement plate instead can I use bacterological petri dish ?
10 October 2019 5,587 2 View
Hello, I am thinking to get fresh water by Reverse Osmosis and store it in tank. Is there any study related water quality after long time storage?let's say one year. Thank you
15 September 2019 6,557 8 View
Hello, I am very beginner in TRNSYS. By default the simlation in TRNSYS is hourly. However, I want to plot a graph based on its month. For example, electricity production every month: January,...
07 May 2019 1,043 4 View
it is about data mining,
13 January 2018 1,186 4 View
Hi, i wanted to modelling some of variation of winding of transformer, like figure 5.a (see my attachment), i wanted to see inductances in the transformer, but after i did simulation, i just got...
20 January 2017 787 3 View
i want to find the leakage inductance of toroidal transformer, so tried to do some of FEM simulation with ansys and femm. but the result of inductance is different between them, i tried to consul...
08 December 2016 4,162 6 View
Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,
02 March 2021 0 0 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...
01 March 2021 9,911 3 View
I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...
01 March 2021 8,668 3 View
I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...
01 March 2021 736 3 View
I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...
01 March 2021 8,415 1 View
How can one improve mesh skewness, orthogonality, aspect ratio?
28 February 2021 7,730 3 View
I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...
28 February 2021 552 3 View
Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...
27 February 2021 5,969 1 View
In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...
26 February 2021 3,806 2 View