Coating of graphene?

04 April 2018 1 2K Report

how can i cotaed a graphene powder on a copper foil ? need your suggestion please

Dear Faisal Nazeer,

You can prepare the dispersion of graphene powder and then employ the graphene coating on Cu or any desired substrate by:

1. Spin coating when your sample is small (~1 cm2)

2. Spray or Drop Casting when your sample is large

Badges
Science topic

More Faisal Nazeer's questions See All

Graphene powder, nanoribbons, nanoplatelets?

what's the difference between graphene powder, nanoribbons and graphene nanoplatelets? Need your valueable comments

03 April 2018 3,813 2 View

Solvent for graphene?

anyone know anout the good solvent that i can mix the graphene in the solvent and after that solvent will evaporate at room temerature?

03 April 2018 4,705 3 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,368 2 View

How can I separate graphene from amorphous carbon of similar particle sizes?

The starting material is a finely ground powder. Some particles contain more graphene than others.

30 July 2024 3,978 2 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Addition of EDTA during the synthesis of copper nanoparticles to prevent it from being oxidized?

I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...

28 July 2024 8,027 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View